manualshive.com logo in svg

Paradyne COMSPHERE 3610, Operator'S Manual

The Paradyne COMSPHERE 3610 user manual is available for free download from our website. This essential guide provides detailed instructions and information about the product's functionalities. Explore its comprehensive features and troubleshooting tips by simply visiting manualshive.com and easily accessing the manual.

Share
Download
background image

COMSPHERE 3600 Series Data Service Units

1-12

July 1999

3610-A2-GB91-90

Figure 1-4. NMS Interfaces to the SDU (2 of 2)

In-band Secondary Channel Transport

Based upon your entry for the Diag Type (Diagnostic

Type) configuration option within the Diag (Diagnostic)
option set, one of three methods used for in-band
secondary channel transport may be selected:
nondisruptive diagnostics, disruptive diagnostics, and
mixed diagnostics. The following paragraphs describe
each of these methods. Refer to 

Tables 6-2

, 

6-3

, and 

6-4

,

Diagnostic Configuration Options (DSU, DBM, and
General), in Chapter 6 for a description of the
configuration option.

NOTE

Even though the DSU is
configured for nondisruptive
diagnostics, it will also accept
disruptive commands.

Nondisruptive Diagnostics

In a nondisruptive diagnostic network, diagnostic data

is transmitted without interrupting user-transmitted data.
In addition, nondisruptive diagnostics allow the control
DSU to obtain real-time health and status data from its
tributary DSUs and extended circuits. This type of
network is provided through an in-band secondary
channel transport capability. The in-band secondary
channel transport carries diagnostic data while the
user-transmitted data is sent over the primary channel
without interruption.

Three nondisruptive diagnostic techniques are used by

the 3600 Series DSUs. The technique used is dependent
upon whether the circuit is configured for point-to-point,
multipoint, or multichannel multipoint (MCMP). The
technique selected is determined by your LinkConfig
(Link Configuration) selection under the Diagnostic
General option set and MUX Setup configuration options
(

Tables 6-4

 and 

6-9

 through 

6-11

 in Chapter 6

 

of this

guide).

Summary of Contents for COMSPHERE 3610























































































































































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 3610

FALCOM SAMBA3G-G Manual preview
SAMBA3G-G
Brand: FALCOM Pages: 22
Verizon Wireless USB551L User Manual preview
USB551L
Brand: Verizon Wireless Pages: 37
Paraben Photo Backup Stick Universal Quick Start Manual preview
Photo Backup Stick Universal
Brand: Paraben Pages: 10
NETGEAR Nighthawk C7000 Quick Start Manual preview
Nighthawk C7000
Brand: NETGEAR Pages: 18
Chonghan CH-M2 User Manual preview
CH-M2
Brand: Chonghan Pages: 46
Traxxas Spartan 57076-1 Owner'S Manual preview
Spartan 57076-1
Brand: Traxxas Pages: 30
Motorola MB7420 Quick Start Manual preview
MB7420
Brand: Motorola Pages: 12
Zte XOHM TU25 User Manual preview
XOHM TU25
Brand: Zte Pages: 27
Konig CMP-MODEMA10 Manual Manual preview
CMP-MODEMA10
Brand: Konig Pages: 5
Microflex MicroLink-HM 101-0029 Installation & Operation Manual preview
MicroLink-HM 101-0029
Brand: Microflex Pages: 17
Exede WiFi Modem User Manual preview
WiFi Modem
Brand: Exede Pages: 12
Moxa Technologies OnCell G2111 Series User Manual preview
OnCell G2111 Series
Brand: Moxa Technologies Pages: 49
PROLiNK PLE901 Quick Installation Manual preview
PLE901
Brand: PROLiNK Pages: 16
PROLiNK PHS300 Quick Installation Manual preview
PHS300
Brand: PROLiNK Pages: 16
Decmetrics ASLH308 Instruction & Setup Manual preview
ASLH308
Brand: Decmetrics Pages: 2
Kajeet Mobile Broadband USB Modem User Manual preview
Mobile Broadband USB Modem
Brand: Kajeet Pages: 46
Hughes R-BGAN User Manual preview
R-BGAN
Brand: Hughes Pages: 68
Micro-Aide LDM-1 plug-in User Manual preview
LDM-1 plug-in
Brand: Micro-Aide Pages: 48

Brands by name

Popular brands

Load more brands