Paradyne COMSPHERE 3610 Operator'S Manual Download Page 114 | Manualshive

Page: 114 / 310

background image

COMSPHERE 3600 Series Data Service Units

4-34

July 1999

3610-A2-GB91-90

Change Protocol Mode

For a 3600 Series DSU, the network management

protocol can be selected from the DCP using the Change
Protocol Mode (ChgMd) feature. The selections available
are:

•

Advanced Diagnostic protocol (ADp), which is
used by the COMSPHERE 6700 or 6800 Series
NMS.

•

DATAPHONE II protocol (DPII), which is used by
the COMSPHERE 6800 Series NMS and by the
DATAPHONE II System Controller, Diagnostic
Console, and Network Controller.

•

Diagnostic MicroComputer protocol (DMC), which
is used by the ANALYSIS 6510 NMS. This
protocol is set on the SDU in a COMSPHERE
3000 Series Carrier if a Model 3611 DSU is used or
from the DCP if a Model 3611 DSU is used.

ChgMd is not available to a tributary DSU or DBM

that is configured for disruptive or no diagnostics (Diag
Type is set to Disr or None), or a single-port multipoint
tributary DSU.

NOTE

DMC protocol is always disruptive
to data. Therefore, you will not be
able to Save (changes) to DMC
protocol if the DSU is configured
for nondisruptive or mixed
diagnostics.

Both the control and tributary DSUs must be

configured for the same protocol, and in a carrier-mounted
configuration, the SDU must be configured for the same
protocol (ADp/DPII or DMC) as the DSU.

To access the ChgMd selections from the top-level

menu, make the following selections:

•

Local (F1), or Remot (F2) and Address

•

Confg

•

ChgMd

If ChgMd is not displayed, press the

or

key to

scroll it into view. The following displays:

F1

Mode:

DPII

Save

DPII

ADp

F2

F3

DMC

F1

Mode:

ADp

Save

DPII

ADp

F2

F3

DMC

After a protocol mode is changed, select Save. You

will not see the Save option if the DCP is locked or if
Diagnostic configuration option, Diagnostic Type (or Diag
Type), is set to NonD or Mixed.

F1

Save Mode:

ADp

Command Complete

F2

F3

Async Terminal

The Async Terminal (Term) feature, available only to

a Model 3610 (standalone) DSU with firmware version
(DSU SW ver) 6.3x or greater, allows you to manage the
DSU through menus displayed using any async terminal.

This feature is enabled or disabled from this subbranch.

Once enabled, the async terminal operates exactly as the
DCP, but without the limitation of the 2-line, 16-character
LCD. An entire menu (or submenu), test result, or range
of configuration option selections appears on a single
screen.

«
...
112
113
114
115
116
...
»

Summary of Contents for COMSPHERE 3610























































































































































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 3610

Brand: XtendLan Pages: 73

Total Access 1240

Brand: ADTRAN Pages: 146

Brand: KaiDeng Pages: 4

Brand: COM 21 Pages: 23

SpeedStream 4200

Brand: Siemens Pages: 8

EDGE Speed ES75

Brand: Siemens Pages: 4

SpeedStream 4100

Brand: Siemens Pages: 9

Brand: Siemens Pages: 2

Brand: Siemens Pages: 16

Brand: Siemens Pages: 20

Gigaset SX685 WiMAX

Brand: Siemens Pages: 32

Brand: Siemens Pages: 56

Brand: Siemens Pages: 51

SIMATIC NET MODEM MD720

Brand: Siemens Pages: 67

Gigaset USB Stick 54

Brand: Siemens Pages: 70

Brand: Siemens Pages: 76

Brand: Siemens Pages: 84

Brand: Siemens Pages: 158

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands