Paradyne COMSPHERE 3610 Operator'S Manual Download Page 271

Page: 271 / 310

NMS Commands Reference

H-5

3610-A2-GB91-90

July 1999

Table H-1

(4 of 4)

NMS Command Set

3600 Series

DSU

COMSPHERE

6700/6800

System

Controller

ANALYSIS

6510

Disruptive

Effect

DSU

ADp or DPII Mode

Controller

6510

Control

Trib

Stat:ID

Identity

Long Status

Confg:Dir

—

List Directory

—

Test:Lpbk

Loopback

Test:Devic

Modem/Device Test

Device Test

Device Self
Test

Stat:TPwr

Report Terminal
Power

—

Bckup:Bkup

Standby Facility

—

Test:BERT

Modem BERT &
Transmit Test
Pattern

—

Send Message

—

Trending Reports

—

Device
NOOP

The disruptive effect of most commands depends on the position of the addressed device in the circuit

and the setting of the Diagnostic Type configuration option. Commands addressed to a control DSU use
the NMS control channel (CC) or diagnostic channel (DC), and are nondisruptive to the primary data

channel. Since a tributary is remote, commands addressed to it can be disruptive unless the associated

DBMs are in Standby mode or the DSU is configured for nondisruptive mode.

E = If the DSU is configured for disruptive or mixed diagnostics, this command may cause errors

requiring retransmission of data. If the DSU is configured for nondisruptive diagnostics, this
command will not cause errors in the user data.

N = Nondisruptive.

D = Session-disruptive.

Session-nondisruptive but may cause errors requiring retransmission of data.

Command cannot be addressed to a tributary DSU by the ANALYSIS 6510 NMS if the firmware release is

less than 2.4.

A Standby facility addressed to a DBM/DBM-V/DBM-S/DBM-D performs a Dial Mode/Dial Standby

command.

To terminate the Transmit Test Pattern command, execute an Abort command to the tributary DSU instead

of using a TTP release command.

Session-disruptive depending upon test type.

Summary of Contents for COMSPHERE 3610























































































































































































































































































































Search results

Summary of Contents for COMSPHERE 3610

Reviews:

Related manuals for COMSPHERE 3610

Brands by name

Popular brands

Paradyne COMSPHERE 3610, Operator'S Manual

Search results

Summary of Contents for COMSPHERE 3610

Reviews:

Related manuals for COMSPHERE 3610

Brands by name

Popular brands