background image

CAUTION

•

Install or remove modules from the shelf only when the power is off.
If you install a module in the shelf with the power on, the internal

circuitry may suffer damage and the product warranty will be void.

•

Remove and install circuit boards only in a static-safe environment
(use antistatic wrist straps, smocks, footwear, etc.).

•

Keep circuit boards in their antistatic bags when they are not in use.

•

Do not ship or store circuit boards near strong electrostatic, electromag-
netic, magnetic, or radioactive fields.

•

For more complete information on electrostatic discharge safety
precautions, refer to Bellcore

TM

 Technical Reference # TR-NWT-000870.

Copyright 1998 by Dantel, Inc. • Dantel is a registered trademark of Dantel, Inc. • ISO 9001 Registered

Printed in the U.S.A.

I

NSTALLATION

 & O

PERATION

 M

ANUAL

44202-0898 <90-00004>

44202

202 C

OMPATIBLE

M

ODEM

About this Practice:

This practice has been reissued to:
• Replace modem alignment

procedure and Table C, in 

Installa-

tion section, with new procedure.

Issue date: August 1998

Reissued Practices: Updated
and new content can be identified
by a banner in the right margin.

UPDATED

Table of Contents

Ordering Information ............................................................................  2
General Description ...............................................................................  2
Circuit Description ................................................................................  2
Application Information .........................................................................  5
Installation ............................................................................................  6
Operation .............................................................................................  12
Technical Specifications.......................................................................  14
Warranty .............................................................................................  16

44202-00

202 MODEM

A11-44202-00 REV__

ON

TEST

MON

XMT

4W

2W

LINE

MON

LINE

ON

ABL

ON

DLB

TD

RD

RTS

CD

DTR

CTS

XMT

LEVEL

RCV

GND

RCV

Summary of Contents for 44202

















Reviews: