manualshive.com logo in svg

otometrics Hortmann Vestlab 100, User Manual

Share
Download
otometrics Hortmann Vestlab 100 User Manual Download Page 94

92

Otometrics

Vestlab Safety

 

Warning Notes 

7.2

Warning Notes 

Note 1:
There are no user-serviceable parts inside the Hortmann Vestlab 100 cabinet. For the 
sake of safety, and in order not to void the warranty, the cabinets should only be 
opened and serviced by authorized service personnel. In case of defects, please make 
a detailed description of the defect(s) and contact your supplier. Do not use a defec-
tive instrument.

Note 2: 
Keep Hortmann Vestlab 100 away from liquids. Do not allow moisture inside the 
instrument.

Note 3:
Do not use the instrument in the presence of flammable anesthetics (gases).

The instrument is marked with this symbol to indicate 
that it is electronic equipment covered by the Directive 
200296/EC on waste electrical and electronic equipment 
(WEEE).

Hortmann Vestlab 100 is marked with this symbol to indi-
cate it is suitable for direct current.

Symbols on the Hortmann Vestlab 100 back panel, see 

Device setup and software installation

6

.

Hortmann Vestlab 
100 Symbols

Hortmann Vestlab 100
Warning Notes

Equipment connected to the displayed connectors 
must be certified to relevant EN/IEC safety standards, 
e.g., EN/IEC 60950. Mains connected equipment - 
except EN/IEC 60601-1 certified equipment - must 
be powered from the Powertronix Isolation Station.

The Hortmann Vestlab 100 should only be connected 
to power adapter type FW73623M/15 from Friwo. 
For continued protection against fire hazard, replace 
fuse with the same type and rating only.

Summary of Contents for Hortmann Vestlab 100







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands