Omron SCARA YRCX Series Programming Manual Download Page 96

Page: 96 / 506

8-4 Chapter 8 Robot Language Lists

No.

Name

Description

Online

Type

MCHREF

Acquires the return-to-origin or absolute-search machine

reference value for specified robot axes. (Valid only for axes

whose return-to-origin method is set as "sensor" or "stroke-

end".)

Function

MID$

Extracts a character string of a desired length from a

specified character string.

Function

Outputs a specified value to the MO port or acquires the

MO status.

Command /

Function

MOTOR

Controls the motor power status.

Command

MOVE

Performs absolute movement of all axes of a specified robot.

Command

MOVEI

Performs relative movement of all axes of a specified robot.

Command

MOVET

Performs relative movement of all axes of a specified robot

when the tool coordinate is selected.

Command

MTRDUTY

Acquires the motor load factor of the specified axis.

Function

OFFLINE

Sets a specified communication port to the "offline" mode.

Command

ON ERROR

GOTO

This command allows the program to jump to the error

processing routine specified by the label without stopping

the program, or it stops the program and displays the error

message.

Command

ON to GOSUB

Jumps to a subroutine with labels specified by a GOSUB

statement in accordance with the conditions, and executes

that subroutine.

Command

ON to GOTO

Jumps to label-specified lines in accordance with the conditions.

Command

ONLINE

Sets the specified communication port to the "online" mode.

Command

OPEN

Opens the specified General Ethernet Port.

Command

ORD

Acquires the character code of the first character in a

specified character string.

Function

ORGORD

Specifies/acquires the axis sequence parameter for

performing return-to-origin and an absolute search

operation in a specified robot.

Command /

Function

ORIGIN

Performs return-to-origin.

Command

OUT

Turns ON the bits of the specified output ports and

terminates the command statement.

Command

OUTPOS

Specifies/acquires the "OUT position" parameter of a

specified robot.

Command /

Function

PATH

Specifies the PATH motion path.

Command

PATH END

Ends the path setting for PATH motion.

Command

PATH SET

Starts the path setting for PATH motion.

Command

PATH START

Starts the PATH motion.

Command

PDEF

Defines the pallet used to execute pallet movement commands.

Command

PGMTSK

Acquires the task number in which a specified program is

registered.

Function

PGN

Acquires the program number from a specified program

name.

Function

PMOVE

Executes the pallet movement command of a specified robot.

Command

Defines points within a program.

Command

PPNT

Creates point data specified by a pallet definition number

and pallet position number.

Function

Displays a character string at the programming box screen.

Command

Summary of Contents for SCARA YRCX Series



























































































































































































































































































































































































































































































































Search results

Summary of Contents for SCARA YRCX Series

Reviews:

Omron SCARA YRCX Series, Programming Manual, Page: 96 / 506

Search results

Summary of Contents for SCARA YRCX Series

Reviews: