manualshive.com logo in svg

Omron SCARA YRCX Series, Programming Manual, Page: 268 / 506

Share
Download
Omron SCARA YRCX Series Programming Manual Download Page 268

8-176     Chapter 8  Robot Language Lists

88

N

O

P

Q

R

S

T

U

V

W

X

Y

Z

 

94

 

PUSH

Executes a pushing operation for specified axes

Format

PUSH [robot number](axis number, expression), option, option

 Values 

 

robot number

 .........................1 to 4 (If not input, robot 1 is specified.)

  

axis number

 ...........................1 to 6

  

expression

 ..............................Motor position (mm, degree, pulse) or point expression

 Explanation 

  Executes an absolute position movement of the specified axis with controlling the 

pushing thrust in the forwarding direction.

   

• Movement type :   Pushing PTP movement of specified axis

   

• Point data setting : Direct coordinate data input, point definition

   

• Options : 

 Pushing thrust setting, pushing time, pushing speed setting, 
STOPON setting

Movement type 

 

●

PTP (point-to-point) of specified axis

PTP  movement begins after the operation of the axis specified by the <axis number> is 
completed (within the tolerance range), controlling the pushing thrust in the forwarding 
direction of the axis.

The conditions to start the pushing control are as follows.
• Immediately after the start of movement of an axis by the PUSH statement
•  After the merge operation is completed (when the PUSH statement is specified in the line 

next to the movement command with CONT specified)

The conditions to terminate the command are as follows.
• The axis arrives within the tolerance range of the target position.
•  The status where the pushing thrust of the axis reaches <

pushing thrust value

> elapses the 

time specified to <

pushing time value

>.

The end status for the PUSH statement can be confirmed with the PSHRSLT statement.

The conditions to cancel the pushing thrust are as follows.
•  When a movement command is executed after the PUSH command including STOP is 

finished

• When a servo off occurs
• When the power source to the controller is interrupted and restarted

Summary of Contents for SCARA YRCX Series



























































































































































































































































































































































































































































































































Reviews:

No comments