manualshive.com logo in svg

Omron SCARA YRCX Series, Programming Manual, Page: 414 / 506

Share
Download
Omron SCARA YRCX Series Programming Manual Download Page 414

7

8

9

10

11

12

13

11-4     Chapter 11  User program examples

1.4 

Palletizing

1.4.1 

Calculating point coordinates

 

■

Overview

Repetitive movement between a fixed work supply position P0 and each of the equally spaced 
points on a pallet can be performed with the following program.
In the drawing below, points N1 to N20 are on Cartesian coordinates, consisting of 5 points 
positioned at a 50mm pitch in the X-axis direction and 4 points at a 25mm pitch in the Y-axis 
direction. The robot arm moves from point to point in the order of P0-N1-P0-N2...N5-P0-N6-P0... 
while repeatedly moving back and forth between point P0 and each pallet.

POINT DATA

Work supply position:
 

 

 

P0= 

0.000 0.000 0.000  0.000 0.000 0.000

X-axis pitch:
 

 

 

P10=  50.000 0.000 0.000  0.000 0.000 0.000

Y-axis pitch:
   P20= 

0.000 

25.000 

0.000 

0.000 

0.000 

0.000

N1 position:
   P1 = 

100.000 

50.000 

0.000 

0.000 

0.000 

0.000

Calculating point coordinates

X+

N16

N17

N18

N19

N20

N11

N12

N13

N14

N15

N6

N7

N8

N9

N10

N1

N2

N3

N4

N5

50

25

P0

Y+

33C04-R7-00

Processing flow

START

Movement to supply position.
Movement to P100
P100 is shifted by the pitch amount 
in the X-direction.

P200=P1
P100=P1

Repeat 5 times

Repeat 4 times

Movement to P0

Movement to P100

P100=P100+P10

STOP

P200=P200+P20

P100=P200

P1 coordinates are input at P200.
P1 coordinates are input at P100.

Movement to P200
P200 is shifted by the pitch amount 
in the Y-direction.

31C05-R7-00

Summary of Contents for SCARA YRCX Series



























































































































































































































































































































































































































































































































Reviews:

No comments