Omron SCARA YRCX Series Programming Manual Download Page 108

Page: 108 / 506

8-16 Chapter 8 Robot Language Lists

Functions: operation-specific

Point related functions

No.

Function name

Description

JTOXY

Converts joint coordinate data to Cartesian coordinate data of a specified robot.

(

↔

XYTOJ)

LOCx

Acquires point data for a specified axis or shift data for a specified element.

PPNT

Creates point data specified by a pallet definition number and pallet position number.

141 WHERE

Reads out the current position of the arm of a specified robot in joint coordinates

(pulse).

143 WHRXY

Reads out the current position of the arm of a specified robot as Cartesian

coordinates (mm, degrees).

144 XYTOJ

Converts the point variable Cartesian coordinate data to the joint coordinate data

of a specified robot. (

↔

JTOXY).

Parameter related functions

No.

Function name

Description

ABSRPOS

Acquires the machine reference value for specified robot axes. (Valid only for

axes whose return-to-origin method is set as "mark".)

ACCEL

Acquires the acceleration coefficient parameter of a specified robot.

ARCHP1

Acquires the arch position 1 parameter of a specified robot.

ARCHP2

Acquires the arch position 2 parameter of a specified robot.

ARMCND

Acquires the current arm status of a specified robot.

ARMSEL

Acquires the current "hand system" setting of a specified robot.

ARMTYP

Acquires the "hand system" setting of a specified robot.

AXWGHT

Acquires the axis tip weight parameter of a specified robot.

CURTQST

Acquires the current torque value ratio of a specified axis to the rated torque.

CURTRQ

Acquires the current torque value of the specified axis of a specified robot.

DECEL

Acquires the deceleration rate parameter of a specified robot.

LEN

Acquires the length (byte count) of a specified character string.

MCHREF

Acquires the return-to-origin or absolute-search machine reference for specified

robot axes. (Valid only for axes whose return-to-origin method is set as "sensor"

or "stroke-end".)

MTRDUTY

Acquires the motor load factor of the specified axis.

ORD

Acquires the character code of the first character in a specified character string.

ORGORD

Acquires the axis sequence parameter for performing return-to-origin and an

absolute search operation of a specified robot.

OUTPOS

Acquires the "OUT position" parameter of a specified robot.

PSHFRC

Acquires the "Push force" parameter.

PSHJGSP

Acquires the push judge speed threshold parameter.

PSHMTD

Acquires the push method parameter.

PSHRSLT

Acquires the status at the end of the PUSH statement.

PSHSPD

Acquires the push speed parameter.

PSHTIME

Acquires the push time parameter.

133 TOLE

Acquires the tolerance parameter of a specified robot.

134 TORQUE

Acquires the maximum torque command value which can be set for a specified

axis of a specified robot.

139 WEIGHT

Acquires the tip weight parameter of a specified robot.

Summary of Contents for SCARA YRCX Series



























































































































































































































































































































































































































































































































Search results

Summary of Contents for SCARA YRCX Series

Reviews:

Omron SCARA YRCX Series, Programming Manual, Page: 108 / 506

Search results

Summary of Contents for SCARA YRCX Series

Reviews: