TOMPYEUOQ2A03C AC Drive Q2A Installation and Operation Instructions
11
Symbol
Name
Function
G
STOP Key
Stops drive operation.
Note:
Uses a stop-priority circuit. Push
to stop the motor even when a Run command is active at MFDI terminals. Set
o2-02 = 0
[STOP Key Selection of Function = Disabled]
to disable the priority in
.
H
Left Arrow Key
•
Moves the cursor to the left.
•
Back to the previous screen.
Up Arrow Key/Down
Arrow Key
/
•
Scrolls up or down to display the next item or the previous item.
•
Selects parameter numbers, and increments or decrements setting values.
Right Arrow Key (RESET)
•
Moves the cursor to the right.
•
Continues to the next screen.
•
Restarts the drive to clear a fault.
ENTER Key
•
Enters parameter values and settings.
•
Selects menu items to move the user between keypad displays.
•
Selects each mode, parameter, and set value.
I
RUN Key
Starts the drive in LOCAL Mode.
Starts the operation in Auto-Tuning Mode.
Note:
Push
on the keypad to set the drive to LOCAL Mode before operating the motor with the keypad.
J
USB Terminal
Insertion point for a USB cable (USB 2.0, type: A - mini-B). Use the USB cable to connect the drive to a PC.
K
RJ-45 Connector
Connects to the drive using an RJ-45 8-pin straight through UTP CAT5e cable or keypad connector.
L
Clock Battery Cover
Remove this cover to install or replace the clock battery.
WARNING
Sudden Movement Hazard. The drive may start unexpectedly if switching control sources when setting b1-07
= 2 [LO/RE Run Selection = Accept RUN]. Clear all personnel from rotating machinery and electrical connections prior to
switching control sources. Failure to comply may cause death or serious injury.
■
Keypad Mode and Menu Displays
Note:
•
Energize the drive with factory defaults to show the Initial Setup screen. Push
(Home) to show the HOME screen.
–
Select [No] from the [Show Initial Setup Screen] setting to skip Initial Setup screen during power up.
•
Push
from the Home screen to show drive monitors.
•
Push
to set
d1-01 [Reference 1]
when the Home screen shows
U1-01 [Frequency Reference]
in LOCAL Mode.
•
The keypad will show [Rdy] when the drive is in Drive Mode. The drive is prepared to accept a Run command.
•
The drive will not accept a Run command in Programming Mode in the default setting. Set
b1-08 [RUN@PRG Mode Selection]
to
accept or reject a Run command from an external source while in Programming Mode.
–
Set
b1-08 = 1 [NoRUN@Program]
to reject the Run command from an external source while in Programming Mode (default).
–
Set
b1-08 = 2 [RUN@Program]
to accept the Run command from an external source while in Programming Mode.
–
Set
b1-08 = 3 [Program@Stop only]
to prevent changes from Drive Mode to Programming Mode while the drive is operating.
EN
Summary of Contents for Q2A-A Series
