manualshive.com logo in svg

Omron H2A -, Manual

Share
Download
Omron H2A - Manual Download Page 75

H3DR-A/P/M

H3DR-A/P/M

75

I/O Functions

H3DR-A/-AS/-AP/-ASP

Inputs

Start

Starts time-measurement.

Reset

Interrupts time-measurement and resets preset time-measurement value. No time-measurement is
made and control output is OFF while the reset input is ON.

Gate

Prohibits time-measurement.

Output

Control output

Outputs are turned ON according to designated output mode when preset value is reached.

H3DR-P/-PP

Input

Start

Starts time-measurement.

Output

Control output

Output is turned ON according to designated output mode when preset value is reached.

H3DR-M

Input

No input is available.

Output

Control output

Output is turned ON when preset value is reached.

Basic Operation

H3DR-A

j

/-AS

j

/-P

j

Setting of Selector

The selectors can be turned clockwise and counterclockwise to se-
lect the desired time unit, time scale, or operating mode.
Each selector has a snap mechanism that secures the selector at a
given position. Set the selector at a position at which it is secured.
Do not set it midway between two securing positions or a malfunc-
tion could result from improper setting.

A

Operating
mode selector

Groove for
screwdriver

Operating
mode display
window

Selection of Operating Mode

Turn the operating mode selector with a screwdriver until the de-
sired operating mode (A, B, B2, C, D, or E) appears in the display
window located below the selector.

Selection of Time Unit and Time Scale

The desired time unit (s, m, h, or 10h) can be displayed in the win-
dow above the time setting dial by turning the time unit selector lo-
cated at the upper right corner of the front panel. Time scale (0.1 or
1) is selected with the time scale selector at the upper left corner of
the front panel, it appears in the window above the selector.

Scale range
selector

Scale range
display window

Time unit selector

Time unit display
window

Setting of Time

The desired time is set with the time setting dial. This time can be
fine-tuned by adjusting the fine-tuning dial (the reduction ratio of the
fine-tuning dial is 1:6). The fine-tuning dial is useful when delicate
and more accurate adjustment is required.

Fine-tuning dial

Time setting
dial

H3DR-M

The H3DR-M does not incorporate a scale range selector, operating
mode selector, or fine-tuning.

Summary of Contents for H2A -







































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands