Home
/
Omron
/
H2A -
/
Manual

Omron H2A -, Manual

Share

Page: 202 / 326

Omron H2A - Manual Download Page 202

H5CN

H5CN

202

Specifications

Ratings

Item

Contact output

Solid-state output

Supply voltage

100 to 240 VAC (50/60 Hz), 12 to 48 VDC
(permissible ripple: 20% max.) (see note)

12 to 48 VDC (permissible ripple: 20% max.)

Operating voltage range

85% to 110% of rated supply voltage

Power consumption

Approx. 12 VA (at 240 VAC, 50 Hz),
approx. 2.5 W (at 48 VDC)

Approx. 2.5 W (at 48 VDC)

Resetting system and
gate input

Reset by power-OFF (not provided for models with backup power for memory protection):
min. power OFF time: 0.5 s
External reset or gate (common to contact and solid-state inputs): min. reset input signal width: 0.02 s;
residual voltage: 2 V max.

Control outputs

SPDT: 3 A at 250 VAC, resistive load (cos

%

= 1)

Open collector: 100 mA max. at 30 VDC max.

Note:

Models with memory backup function are not available for this range of DC supply voltages.

Characteristics

Accuracy of operating time

!

0.01%

!

0.05 s max. (see note 1),

!

0.005%

!

0.03 s max. (see note 2) (see note 3)

Setting error

Influence of voltage

Influence of temperature

Insulation resistance

100 M

$

min. (at 500 VDC) (between current-carrying terminal and exposed non-current

carrying metal parts, between power supply circuit and control output circuit)

Dielectric strength

2,000 VAC, 50/60 Hz for 1 min (between current-carrying terminal and exposed
non-current-carrying metal parts, between power supply circuit and control output circuit)

Vibration resistance

Destruction: 10 to 55 Hz with 0.75-mm double amplitude
Malfunction: 10 to 55 Hz with 0.5-mm double amplitude

Shock resistance

Destruction: 300 m/s

2

(approx. 30G)

Malfunction: 100 m/s

2

(approx. 10G)

Ambient temperature

Operating: --10

"

C to 55

"

C

Storage:

--25

"

C to 65

"

C

Ambient humidity

Operating: 35% to 85%

Life expectancy

Mechanical: 10,000,000 operations min. (under no load at 1,800 operations/h)
Electrical:

100,000 operations min. (3 A at 250 VAC, resistive load)

Approved standards

UL (File No. E41515), CSA (File No. LR22310)

Weight

Approx. 150 g

Note:

1. When timer operation is started by power application.

2. When timer operation is started after a reset input has been applied.

3. These values represent the total accuracy of the timer including the repeat accuracy, setting error, and variation due to voltage and

temperature changes. Note that they also comprise errors due to the rise time of the power source and the operating times of the
internal and output circuits.

«
...
200
201
202
203
204
...
»

Summary of Contents for H2A -







































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands