Omron H2A - Manual Download Page 132

Page: 132 / 326

132

Solid-state Timer

H3M

Solid-state Timer with Variable Time
Ranges

Four time ranges are selectable per timer unit.

Wide timing range of 0.05 second to 30 hours can
be covered by a combination of five timer units.

Standard surface mounting type is easily convert-
ible to flush mounting type with the use of a special
adapter (Y92F-40).

Requires only 40 x 50 mm for mounting space.

Equipped with power-ON & time-out indicators.

Ordering Information

Operation/resetting system

Time-limit

Instantaneous

Mounting

g y

contact

Surface mounting

Flush mounting

Time-limit operation/

tti

DPDT

---

H3M

H3M with Y92F-40 adapter

self-resetting

SPDT

H3M-H

H3M-H with Y92F-40 adapter

Note:

1. Specify both the model number and supply voltage when ordering.

2. Sockets and adapters for surface/track mounting are available optionally and therefore, place the order for them as necessary.

Timer hold-down clips (F-hook and L-hook) are supplied with the timer.

Accessories (Order Separately)

Adapter
Y92F-40

Specifications

Time Ranges

Four time ranges are available for each timer by changing the time range selector switch positions to different combinations.

Time range code

Time range selector switch

0.05 to 0.5 s

0.5 to 5 s

0.05 to 0.5 min

0.5 to 5 min

0.1 to 1 s

1 to 10 s

0.1 to 1 min

1 to 10 min

0.3 to 3 s

3 to 30 s

0.3 to 3 min

3 to 30 min

Time range code

Time multiplying key

0.1 to 1 min

1 to 10 min

0.1 to 1 hrs

1 to 10 hrs

0.3 to 3 min

3 to 30 min

0.3 to 3 hrs

3 to 30 hrs

Summary of Contents for H2A -







































































































































































































































































































































Search results

Summary of Contents for H2A -

Reviews:

Brands by name

Popular brands

Omron H2A -, Manual

Search results

Summary of Contents for H2A -

Reviews:

Brands by name

Popular brands