manualshive.com logo in svg

Omron H2A -, Manual

Share
Download
Omron H2A - Manual Download Page 311

H3BF

H3BF

311

Installation

Connection

Precautions

How to Change Time Unit and Rated Time

The desired time unit (sec, min, hrs, or 10 h) can be displayed in the
window below the time setting knob by turning the time unit selector
(i.e., rotary switch) located at the lower right corner of the front pan-
el. Dial digits appear in the six windows around the time setting knob
according to the rated time selected by turning the rated time selec-
tor (i.e., rotary switch) located at the lower left corner of the front
panel.

The following digits will appear in the respective dial digit display
windows:

Rated time

Dial digits

0.5

0, 0.1, 0.2. 0.3, 0.4, 0.5

1

0, 0.2, 0.4, 0.6, 0.8, 1.0

5

0, 1, 2, 3, 4, 5

10

0. 2. 4. 6. 8. 10

Time unit selector

Dial digit display
windows

Rated time
selector

Time unit display window

Switch Setting

The selector switches for time unit, scale, and function can be
turned in both directions, clockwise and counterclockwise. Each se-
lector switch has a snap mechanism that secures the switch at a giv-
en position. Set the switch at a position at which it is secured. Do not
set it midway between two securing positions because such prac-
tice may causes the Timer to malfunction or, in the worst case, break
down.
Accurately move and set the scale selector switch, matching the 0
position mark to a division on the scale.

Caution

Do not change the time unit, or operation mode while the Timer
is in operation. Otherwise, the Timer may malfunction or suffer
from damage. Be sure to turn off the power supply of the Timer
before changing the time unit, rated time or operation mode.

WARNING

Electrical Shock Hazard

Never touch the input terminals of any H3BG Timer while pow-
er is being applied to the Timer.

!

!

Summary of Contents for H2A -







































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands