manualshive.com logo in svg

Omron H2A -, Manual

Share
Download
Omron H2A - Manual Download Page 29

H3CR-A

H3CR-A

29

End Plate
PFP-M

Spacer
PFP-S

50

11.5

M4 x 8
pan head
screw

10

6.2

1.8

1

35.5 35.3

1.8

1.3

4.8

5

16

12

44.3

34.8

16.5

10

Protective Cover
Y92A-48B

The protective cover protects the front panel, particularly the time
setting section, against dust, dirt, and water. It also prevents the set
value from being altered due to accidental contact with the time set-
ting knob.

Note:

1. The Y92A-48B Protective Cover is made of a hard plas-

tic and therefore it must be removed to change the timer
set value.

2. The Protective Cover cannot be mounted if the Panel

Cover (sold separately) is used on the Timer.

Y92A-48B

Time Setting Ring/Panel Cover

There are three types of Panel Covers (Y92P-48GL, Y92P-48GB,
and Y92P-48GM), all of which are available in three colors. Use the
most suitable type of Panel Cover with the design of the scaling
plate according to the application.
When setting a given time for the Timer, use of the Y92S-27 or
Y92S-28 Time Setting Ring facilitates the time setting operation and
minimizes possible setting errors by operators.

The Time Setting Ring and Panel Cover should be used as a pair.

Setting a specific
time

Time Setting Ring A (Y92S-27) and
Panel Cover (Y92P-48GL, -48GB, or
-48GM)

Limiting the setting
range

Time Setting Ring B or C (Y92S-28),
and Panel Cover (Y92P-48GL, -48GB,
or -48GA)

Y92S-27
Time Setting A

Y92S-28
Time Setting B

Y92P-48GL
Light Gray

Y92P-48GB
Black

Y92P-48GM
Medium Gray

Y92S-28
Time Setting C

Hold-down Clip

Y92H-7/-1
For PL08 and PL11 Sockets

Y92H-8/-2
For PF085A Socket

Summary of Contents for H2A -







































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands