manualshive.com logo in svg

Omron H2A -, Manual

Share
Download
Omron H2A - Manual Download Page 48

H3CR-G

H3CR-G

48

Using the Setting Ring

Setting a Specific Time

Mount the Panel Cover on the Timer, set the desired time with the time setting knob, and place Time Setting Ring A onto the time setting knob so
that the time setting notch of Time Setting Ring A is in the center of the reset lock position of the Panel Cover.

Time setting
notch

Reset lock position

Time Setting Ring A

Panel Cover

Example: To set the time to 10 s.

Time setting notch

Setting position

Limiting the Setting Range

Example: To set a range of 10 and 20 s.
Mount the Panel Cover on the Timer, set the time setting knob to 10 s (the lower limit of the setting range), and place Time Setting Ring C onto
the time setting knob so that the stopper of Time Setting Ring C is on the right edge of the reset lock position of the Panel cover. Next, set the time
setting knob to 20 s (the upper limit of the setting range), place Time Setting Ring B onto the time setting knob so that the stopper of Time Setting
Ring B is on the left edge of the reset lock position of the Panel Cover.

Stopper

Reset lock position

Time Setting
Ring B

Time Setting
Ring C

Panel Cover

Range

Timing Chart

Model

Timing chart

H3CR-G8L/-G8EL

t1

t2

0.5 s min.

Power (2 -- 7)

Instantaneous output
(1 -- 3) (-E models)

Star operation
output (8 -- 5)

Delta operation
output (8 -- 6)

Star operation indicator

Delta operation indicator

ON

OFF

Lit

Not lit

ON

OFF

ON

OFF

ON

OFF

Lit

Not lit

Note:

t1: Star operation time setting
t2: Star-delta transfer time

Summary of Contents for H2A -







































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands