Omron H2A - Manual Download Page 110

Page: 110 / 326

H3CA

110

Ratings

Item

H3CA-A/H3CA-FA

H3CA-8

H3CA-8H

Rated supply voltage

24 to 240 VAC (50/60 Hz),
12 to 240 VDC (permissible
ripple: 20% max.)

100/110/120, 200/220/240 VAC, (50/60 Hz),
24 VDC (permissible ripple: 20% max.) (see note)

Operating voltage range

90% to 110% of rated supply
voltage

85% to 110% of rated supply voltage

Power consumption

AC: approx. 2 VA
DC: approx. 2 W

AC: approx. 10 VA/1 W
DC: approx. 1 W

AC: approx. 10 VA/1.5 W
DC: approx. 2 W

Control outputs

3 A at 250 VAC, resistive load (cos

= 1)

Note:

Single-phase, full-wave rectified power sources may be used for 24 to 240 VDC.

Characteristics

Accuracy of operating time

0.3%

0.05 s

Influence of voltage

Influence of temperature

Setting error

0.5%

0.05 s

Reset time

H3CA-A/-FA:

0.5 s max.

H3CA-8H/-8:

0.1 s max.

Insulation resistance

100 M

min. (at 500 VDC)

Dielectric strength

2,000 VAC, 50/60 Hz for 1 min (between current-carrying and non-current-carrying parts and
between contact and control circuit)
1,000 VAC, 50/60 Hz for 1 min (between non-continuous contacts)

Vibration resistance

Destruction: 10 to 55 Hz with 0.75-mm double amplitude
Malfunction: 10 to 55 Hz with 0.5-mm double amplitude

Shock resistance

Destruction: 1,000 m/s

(approx. 100G)

Malfunction: 100 m/s

(approx. 10G)

Ambient temperature

Operating: --10

C to 55

Ambient humidity

Operating: 35% to 85%

Life expectancy

Mechanical: 10,000,000 operations min. (under no load at 1,800 operations/h)
Electrical:

100,000 operations min. (3 A at 250 VAC, cos

= 1 at 1,800 operations/h)

Approved standards

UL (File No. E41515), CSA (File No. LR22310), SEV

Weight

H3CA-A:

approx. 110 g

H3CA-FA: approx. 190 g

Engineering Data

operat

ions

)

Load current (A)

Reference: A maximum current of 0.15 A can be switched at 125 VDC (cos

= 1).

Maximum current of 0.1 A can be switched if L/R is 7 ms. In both cases,
a life of 100,000 operations can be expected.

Note:

1. The H3CA Series has been tested for the following: impulse voltages, noise

(via noise simulator, for L loads, and for relay oscillation), and resistance to
static electricity.

2. Minimum applicable load (P reference values):

H3CA-A(FA), H3CA-8H: 100 mA at 5 VDC
H3CA-8: 10 mA at 5 VDC

Summary of Contents for H2A -







































































































































































































































































































































Search results

Summary of Contents for H2A -

Reviews:

Brands by name

Popular brands

Omron H2A -, Manual

Search results

Summary of Contents for H2A -

Reviews:

Brands by name

Popular brands