Omron H2A - Manual Download Page 37

Page: 37 / 326

H3CR-F

Solid-state Twin Timers

H3CR-F

DIN 48 x 48-mm Solid-state Twin Timers

Wide power supply ranges of 100 to 240 VAC and
48 to 125 VDC respectively.

Independent ON- and OFF-time settings. Further-
more, combinations of long ON- or OFF-time and
short OFF- or ON-time settings are possible.

Fourteen time ranges from 0.05 s to 30 h or from
1.2 s to 300 h depending on the model to be used.

Models with a flicker ON start or flicker OFF start
are available.

Easy sequence checks through instantaneous
outputs for a zero set value at any time range.

Only 80 mm long when panel-mounted with a
socket.

11-pin and 8-pin models are available.

Ordering Information

Operating

Supply voltage

0.05 s to 30 h models

1.2 s to 300 h models

modes

11-pin models

8-pin models

11-pin models

8-pin models

Flicker OFF start

100 to 240 VAC

H3CR-F

H3CR-F8

H3CR-F-300

H3CR-F8-300

24 VAC/DC

12 VDC

48 to 125 VDC

Flicker ON start

100 to 240 VAC

H3CR-FN

H3CR-F8N

H3CR-FN-300

H3CR-F8N-300

24 VAC/DC

12 VDC

48 to 125 VDC

Note:

Specify both the model number and supply voltage when ordering.
Example: H3CR-F 24 VAC/DC

Supply voltage

Model Number Legend:

H3CR -

1. Classification
F:

Twin timers

2. Configuration
None: 11-pin socket
8:

8-pin socket

3. Twin Timer Mode
None: Flicker OFF start
N:

Flicker ON start

4. Specified Type
300:

Long time range (1.2 s to 300 h) type

Summary of Contents for H2A -







































































































































































































































































































































Search results

Summary of Contents for H2A -

Reviews:

Brands by name

Popular brands

Omron H2A -, Manual

Search results

Summary of Contents for H2A -

Reviews:

Brands by name

Popular brands