Oki OKIOFFICE 84, User Manual

Page: 62 / 96

62
OKIOFFICE 84
Note: This image function only becomes effective if user
function
17:MEM./FEEDER SW.
is set to
MEM
and/or
user function
25:INSTANT DIALLING
is set to
ON
.
05:SENDER ID 05:SENDER ID 05:SENDER ID 05:SENDER ID 05:SENDER ID
- This function controls the printing of
your machine’s Sender ID on the faxes you send. When turned
on, your machine’s Sender ID, date and time will be printed on
each page slightly outside the image area of your document.
When turned off, your Sender ID, date and time will not be
printed. However, some machines will print your TSI/CSI.
06:MONITOR VOLUME 06:MONITOR VOLUME
06:MONITOR VOLUME 06:MONITOR VOLUME 06:MONITOR VOLUME
- This function sets the volume
your machine uses for telephone line monitoring sounds during
dialling. Available settings are low, high and off
07:BUZZER VOLUME 07:BUZZER VOLUME 07:BUZZER VOLUME 07:BUZZER VOLUME 07:BUZZER VOLUME
- This function sets the volume of
the various beep and alarm tones your machine emits during
operations. Available settings are low, middle and hig.
08:CLOSED NETWORK 08:CLOSED NETWORK 08:CLOSED NETWORK 08:CLOSED NETWORK 08:CLOSED NETWORK
- This function allows you to
program your machine to refuse to receive faxes from or transmit
faxes to locations whose telephone numbers have not been
programmed into your machine’s One Touch keys or
AUTO
DIAL numbers. Using this function, you can set up a closed
network of fax machines. If you do not want your machine to
transmit faxes to or receive faxes from locations outside your
network, select T/R. If you only want your machine to refuse to
receive faxes from outside your network, select RX. Available
settings are OFF, T/R and RX
09:TX MODE DEFAULT 09:TX MODE DEFAULT
09:TX MODE DEFAULT 09:TX MODE DEFAULT 09:TX MODE DEFAULT - This function allows you to
change your machine’s default type of original, transmit and
copy resolution settings. Unless you select otherwise using the
Transmit Resolution/
ô
YES
or Type of Original/
NO
õ
keys, your
machine is set to use the STD and NORMAL settings. If you are
constantly sending faxes which require some other combination
of transmission modes, use this function setting to change the
default transmission modes to any other combination of settings.
While you are programming, the new default combinations will
appear on the LEDs above the Transmit Resolution/
ô
YES
or
Type of Original/
NO
õ
key.
10:T/F TIMER PRG. 10:T/F TIMER PRG. 10:T/F TIMER PRG. 10:T/F TIMER PRG. 10:T/F TIMER PRG.
- When set to the telephone/ fax
answering mode, your machine automatically distinguishes
between incoming voice and fax calls. If the incoming call is a
voice call, your machine will ring to tell you to pick up the
handset. If you do not answer, your machine automatically
switches back to facsimile mode to allow the calling party to
manually send a fax. The
T/F TIMER function controls how
long your machine waits before switching back to fax mode.
Available settings are 20 seconds or 35 seconds
11:RING RESPONSE 11:RING RESPONSE 11:RING RESPONSE 11:RING RESPONSE 11:RING RESPONSE
- This function controls how long
your machine waits before answering an incoming telephone
call when your machine is set to auto receive or telephone/fax
auto switch answering modes. The available settings are 1 ring,
5 seconds, 10 seconds, 15 seconds or 20 seconds.
Note: If your machine is set to telephone/fax auto switch
answering mode, it is recommended that you set ring
response to one ring.