13
- GB -
Safe operation of the unit
−
Keep socket and power plug dry.
−
Route the power cables so that damage is excluded.
−
Do not carry or pull the units by the connection cables. The power connection cables cannot be replaced. If the
cable is damaged, the entire unit has to be disposed of.
−
Never run the pump without water! Otherwise the pump will be destroyed.
−
Never use the pump for fluids other than water. Other fluids could destroy the unit.
−
Never open the unit or its attendant components, unless this is explicitly mentioned in the operating instructions.
−
Never carry out technical modifications to the unit.
−
Only use original spare parts and original accessories for the unit. Only have repairs carried out by authorised
customer service points.
−
Never look directly into the light source of the unit. The light beam's intensity could irreversibly damage the retina.
Pos: 73 /Alle Produkte/Überschriften/H1 Aufstellen @ 7\mod_1202907856718_121.doc @ 43934 @
Installation
Pos: 74 /Lampen/Wasserspieltechnik/Water-Trio/Quintet/Aufstellen Water Trio/Quintet @ 8\mod_1219741451301_121.doc @ 51127 @
Attention! Dangerous electrical voltage.
Possible consequences:
Death or severe injury.
−
Install transformer and 12 V control box at a dry, splash-water protected place. Additionally protect the
12 V control box against sun radiation (max. 40 °C).
−
During operation, ensure that both the transformer and the 12 V control box are placed at a 2 m safety
distance from the bank
(D)
.
Installing the Water Trio / Water Quintet (B, C)
:
Variant 1 (B)
:
−
Install the unit as horizontally as possible in the water on a firm ground.
−
The minimum water level must be just above the pumps
(8)
.
Variant 2 (C)
:
In the case of excessive water depth, the extension tubes
(6)
can be used to compensate. If not sufficient, select a
different suitable place of installation.
−
To open, release the nozzle holders
(9)
by slightly turning them at the housing top section
(10)
and remove.
−
Unscrew the LED light nozzle
(11)
.
−
Screw the extension tubes
(6)
between the LED light nozzles
(11)
and the pumps
(12)
.
−
Close the unit by placing the housing top section
(10)
on the LED light nozzles
(11)
and fasten using the nozzle
holders
(9)
.
−
Install the unit as horizontally as possible in the water on a firm ground.
−
The minimum water level must be just above the pumps
(8)
.
Note
: Ensure that the water inlet at the unit underside is not impaired!
Pos: 75 /Lampen/Wasserspieltechnik/Water-Trio/Quintet/Aufstellung Steuerungsbox und Trafo Water Trio/Quintet @ 8\mod_1219924083632_121.doc @ 51213 @
Installation of the 12 V control box (E, F):
Variant 1 (E)
:
−
Push the ground stake
(5)
fully into the ground at the desired position.
−
Slide the 12 V control box
(3)
onto the ground stake
(5)
.
Variant 2 (F)
:
−
Screw the 12 V control box
(3)
to the ground using 4 screws
(13)
(not included in our scope of delivery) through the
fastening slots
(14)
in the housing of the 12 V control box
(3)
.
Installation of the transformer (G)
:
Install the transformer
(2)
close to the 12 V control box
(3)
.
Note
: Ensure that the cables are routed strain relieved!
Pos: 76 /Alle Produkte/Überschriften/H1 Elektrische Installation @ 8\mod_1219935543509_121.doc @ 51295 @
Electrical installation
Pos: 77 /Lampen/Wasserspieltechnik/Water-Trio/Quintet/INS_Water Trio/Quintet @ 8\mod_1219738775961_121.doc @ 50919 @
'Connect Water Trio / Water Quintet to 12 V control box (G, H)
:
−
Plug the pump plugs
(18)
from Water Trio / Water Quintet and the LED light nozzle plugs
(20)
into the respective
sockets for the pump
(19)
and the LED light nozzles
(21)
of the 12 V control box
(3)
. Note the order of the plugs
(plugs are marked).
−
Insert the connection cable
(17)
of the transformer in the rear socket
(15)
of the 12 V control box
(3)
, then screw-
tighten the cable with the union nut
(16)
.
−
Fit the protection sleeve
(4)
over the 12 V control box
(3)
.
Pos: 78 /Alle Produkte/Überschriften/H1 Inbetriebnahme @ 7\mod_1196625111244_121.doc @ 41417 @
Start-up
Pos: 79 /Lampen/Wasserspieltechnik/Water-Trio/Quintet/INB_Water Trio/Quintet @ 8\mod_1220995735242_121.doc @ 52149 @
Switching on the unit (I)
: Plug the power plug
(22)
of the transformer into the socket.
−
The Water Trio / Water Quintet starts with program 1 (see chapter Operation).
Switching off the unit (I)
: Disconnect the power plug
(22)
of the transformer.
Pos: 80 /Alle Produkte/Dummy_module/===== Seitenwechsel ===== @ 0\mod_1125648978015_0.doc @ 1630 @
