manualshive.com logo in svg

Nortel Passport 5430, Installing And Operating Instructions, Page: 11 / 220

Share
Download
Nortel Passport 5430 Installing And Operating Instructions Download Page 11

306308-A Rev 00

xi

Connecting a Console Modem ...............................................................................4-11

Connecting an External Console Modem  ........................................................4-12

Connecting to an Integrated V.34 Console Modem Module  ............................4-14

Connecting to the AC Power Source  ............................................................................4-16

Using the Cable Looms to Manage Cables  ..................................................................4-17

Where to Go Next  .........................................................................................................4-19

Chapter 5 
Starting the Passport 5430

Understanding the Startup Process  ...............................................................................5-1

Diagnostic Software  .................................................................................................5-2

Using the Diags Command ................................................................................5-3

Installing the Flash Memory Card ...................................................................................5-6

Running the Quick-Start Script  .......................................................................................5-7

Verifying a Successful Installation  ................................................................................5-10

Where to Go Next  .........................................................................................................5-11

Chapter 6 
Operating the Passport 5430

Understanding Passport 5430 LEDs  ..............................................................................6-1

System Processor Card LEDs  .................................................................................6-2

Diagnostic LEDs  ................................................................................................6-2

Module 1 Port LEDs  ..........................................................................................6-4

Expansion Card LED ................................................................................................6-5

PMC Module LEDs ...................................................................................................6-6

Dual Synchronous PMC Module LEDs ..............................................................6-6

ATM T1/E1 PMC Module LEDs  .........................................................................6-7

Turning the Passport 5430 On and Off  ...........................................................................6-9

Resetting the Passport 5430  ........................................................................................6-10

Protecting Flash Memory Card Files  ............................................................................6-11

Removing a Flash Memory Card ..................................................................................6-12

Where to Go Next  .........................................................................................................6-14

Chapter 7 
Replacing the System Processor Card

Where to Go Next  ...........................................................................................................7-8

Summary of Contents for Passport 5430





























































































































































































































Reviews:

No comments