manualshive.com logo in svg

Nortel Passport 5430, Installing And Operating Instructions, Page: 181 / 220

Share
Download
Nortel Passport 5430 Installing And Operating Instructions Download Page 181

306308-A Rev 00

A-1

Appendix A

Passport 5430 Technical Specifications

This appendix provides technical specifications for the Passport 5430 and its 
interface options, as follows:

Physical Specifications

The dimensions and weight of the Passport 5430 are as follows:

•

Height: 5.25 in. (13.3 cm)

•

Width: 17.25 in. (43.8 cm)

•

Depth: 19.75 in. (50 cm)

•

Weight: 32.5 lb (14.75 kg)

Your installation site must provide free space around the Passport 5430 to 
dissipate heat, allow for cable management, and allow CRU installation and 
removal. The space requirements for installing the Passport 5430 are as follows:

•

Width: 22.5 in. (57.2 cm)

•

Minimum depth: 22.25 in. (56.5 cm)

•

Depth for servicing: 38 in. (96.5 cm) 

Topic

Page

Physical Specifications

A-1

Electrical Specifications

A-2

Environmental Specifications

A-2

Hardware Communications Options

A-3

Summary of Contents for Passport 5430





























































































































































































































Reviews:

No comments