manualshive.com logo in svg

Nortel Passport 5430, Installing And Operating Instructions, Page: 77 / 220

Share
Download
Nortel Passport 5430 Installing And Operating Instructions Download Page 77

Accessing the Interior

306308-A Rev 00

3-11

2.

Pull the power supply filler panel away from the Passport 5430.

 

Installing a Power Supply Filler Panel 

To install a power supply filler panel:

1.

Place the power supply filler panel over the empty power supply slot.

2.

Using a flat-tip screwdriver, tighten the captive screw until the power 
supply filler panel firmly covers the slot.

Where to Go Next

Use the following table to determine where to go next. 

Caution: 

To maintain proper cooling, never operate the Passport 5430 with an 

empty power supply slot. Save the filler panel to cover the slot in case you 
need to operate the Passport 5430 with a power supply removed.

For information about

Go to

Installing the Passport 5430 Chassis

Chapter 1

Installing Passport 5430 Customer-Replaceable 
Units for the First Time

Chapter 2

Connecting Cables to the Passport 5430

Chapter 4

Starting the Passport 5430

Chapter 5

Operating the Passport 5430

Chapter 6 

Replacing the System Processor Card

Chapter 7

Adding or Replacing a PMC Module

Chapter 8

Adding or Replacing an Expansion Card

Chapter 9

Adding or Replacing a WAN Adapter Module

Chapter 10

Adding or Replacing a Power Supply

Chapter 11

Passport 5430 Technical Specifications

Appendix A

Worksheets for the Quick-Start Procedure

Appendix B

Summary of Contents for Passport 5430





























































































































































































































Reviews:

No comments