manualshive.com logo in svg

Nortel Passport 5430, Installing And Operating Instructions, Page: 183 / 220

Share
Download
Nortel Passport 5430 Installing And Operating Instructions Download Page 183

Passport 5430 Technical Specifications

306308-A Rev 00

A-3

Hardware Communications Options

The Passport 5430 is designed to scale to your needs. You can add up to three 
expansion or voice processor cards, up to three optional WAN adapter modules, 
one V.34 module, and up to seven PMC modules. 

The Passport 5430 processor card supports:

•

Two Ethernet 10/100BASE-TX interfaces

•

One console interface

The Passport 5430 supports the following PMC modules:

•

One ATM T1/E1 module

•

Up to six dual synchronous modules

The Passport 5430 also supports up to three of the following adapter modules:

•

Serial interface module

•

BRI S/T interface module

•

ISDN BRI U interface module

•

FE1/E1 DSU/CSU interface module

•

FT1/T1 DSU/CSU interface module

•

V.34 modem module

A fourth adapter module slot is dedicated to a V.34 modem for remote console 
management.

Summary of Contents for Passport 5430





























































































































































































































Reviews:

No comments