manualshive.com logo in svg

Nortel Passport 5430, Installing And Operating Instructions, Page: 81 / 220

Share
Download
Nortel Passport 5430 Installing And Operating Instructions Download Page 81

Connecting Cables to the Passport 5430

306308-A Rev 00

4-3

Connecting to the ATM T1/E1 Interface

The ATM T1/E1 PMC module provides one T1 or E1 interface. To connect to the 
ATM T1 interface, see the next section, 

“Connecting to the ATM T1 Interface

.” 

To connect to the ATM E1 interface, see 

“Connecting to the ATM E1 Interface

” 

on 

page 4-4

.

Connecting to the ATM T1 Interface

To connect to the ATM T1 interface on an installed ATM T1/E1 PMC module:

1.

Route the cable from the cable kit (Order number AA0018040) through 
the cable loom slot corresponding to PCI slot 1.

For instructions, see 

“Using the Cable Looms to Manage Cables

” on 

page 4-17

.

2.

Insert the RJ-48C cable connector into the ATM T1/E1 interface 
(

Figure 4-2

).

Figure 4-2.

Connecting the ATM T1/E1 Cable

3.

Connect the other end of the RJ-48C cable to the T1/E1 communications 
device.

4.

Arrange the cable in the cable loom.

For instructions, see 

“Using the Cable Looms to Manage Cables

” on 

page 4-17

.

FBR0063A

Module 3

Module 4

Module 5

Remote
Console

System

Processor

Expansion Card

Expansion Card

Voice Processor

COM

U

ISDN BRI

withNT1

Telco

V.34 Modem

COM

PCI Slot 1

PCI Slot 2

PCI Slot 3

PCI Slot 4

Summary of Contents for Passport 5430





























































































































































































































Reviews:

No comments