Nortel Passport 5430 Installing And Operating Instructions Download Page 172

Page: 172 / 220

Installing and Operating the Passport 5430 Multiservice Access Switch

10-10

306308-A Rev 00

Using a Phillips screwdriver, remove the screw that secures the adapter
module that you want to remove

(Figure 10-5)

Figure 10-5.

Removing the Adapter Module Screw

Pull the adapter module toward you to detach it from the module
connector in the Passport 5430 chassis.

Grasp the adapter module’s metal tab,

(Figure 10-5)

, or insert a thin tool (such

as a flat-tip screwdriver) in the slot on the tab.

Be prepared to apply some force, but stop pulling as soon as the adapter
module is free from the base module connector.

Slide the adapter module all the way out of the slot.

Place the adapter module in an antistatic bag.

FBR0026A

Module 3

Module 4

Module 5

Remote
Console

COM

ISDN BRI

withNT1

Telco

V.34 Modem

DDS

156K/64K
DSU/CSU

ISDN BRI

withNT1

Summary of Contents for Passport 5430





























































































































































































































Search results

Summary of Contents for Passport 5430

Reviews:

Nortel Passport 5430, Installing And Operating Instructions, Page: 172 / 220

Search results

Summary of Contents for Passport 5430

Reviews: