manualshive.com logo in svg

Nortel Passport 5430, Installing And Operating Instructions, Page: 114 / 220

Share
Download
Nortel Passport 5430 Installing And Operating Instructions Download Page 114

Installing and Operating the Passport 5430 Multiservice Access Switch

6-4

306308-A Rev 00

Module 1 Port LEDs

Table 6-2

 describes the system processor card (module 1) Port 1 and Port 2 LEDs.

Slow flashing (green)

System processor card is running its diagnostic 
tests. 

Rapid flashing (green)

System processor card failed its diagnostic tests.

cPCI

Off 

Expansion cards not tested.

On (green) 

One or more expansion cards are installed and 
operating properly. 

Slow flashing (green)

One or more expansion cards are running 
diagnostic tests. 

Rapid flashing (green)

One or more expansion cards failed diagnostic 
tests.

Table 6-2.

System Processor Card Port LEDs

LED

State

Meaning

TX (Transmit)/ 
RX (Receive)

Off

No transmit or receive activity. 

On (green)

Port interface is transmitting or receiving data.

On (amber)

Port interface detects a collision.

SPD

Off

Port is in 10 Mb/s mode.

On (green)

Port is in 100 Mb/s mode.

Link

Off

Link is not active. 

On (green)

Link is active. 

Table 6-1.

System Processor Card Console LEDs

 (continued)

LED

State

Meaning

Summary of Contents for Passport 5430





























































































































































































































Reviews:

No comments