Nortel Passport 5430 Installing And Operating Instructions Download Page 102

Page: 102 / 220

Installing and Operating the Passport 5430 Multiservice Access Switch

5-4

306308-A Rev 00

-long

Runs extensive diagnostic tests on FRU1
and FRU2 specified as follows:
•

cpu (system processor card)

•

ssdb (ATM T1/E1)

•

cmodem (console modem)

•

sdbn (WAN adapter module)
n = 1,2, or 3 indicating the slot
number of the WAN adapter module.
NOTE: 1 is labeled as Module 3 on
the chassis; 2 is labeled as Module 4
on the chassis.

•

cpcin (expansion card)
n = 2, 3, or 4 indicating the PCI slot
number of the expansion card.

•

pmcn@n (dual synchronous PMC)
The first

n = 1 or 2 indicating the PMC

module number. The second

n = 2, 3,

or 4 indicating the PCI slot number of
the expansion card.

You must specify 1 as the slot ID.

If you specify a FRU and then enter
diags1, extensive diagnostics will run on
the specified FRU.

If you do not specify a FRU, extensive
diagnostic tests will run on all of the
FRUs. These tests take up to 5 minutes
per FRU to complete.

Table 5-1.

Diags Command Parameters, Variables, and Functions

Parameter

Variable

Function

Summary of Contents for Passport 5430





























































































































































































































Search results

Summary of Contents for Passport 5430

Reviews:

Nortel Passport 5430, Installing And Operating Instructions, Page: 102 / 220

Search results

Summary of Contents for Passport 5430

Reviews: