manualshive.com logo in svg

Nortel Passport 5430, Installing And Operating Instructions, Page: 201 / 220

Share
Download
Nortel Passport 5430 Installing And Operating Instructions Download Page 201

Worksheets for the Quick-Start Procedure

306308-A Rev 00

B-3

Table B-1

 provides the connector names and numbers that you should use during 

the Quick-Start procedure. 

Filling Out the Quick-Start Sample Worksheets

The inst_pp5400.bat script provides many options for configuring the Passport 
5430 on a network. Because the Passport 5430 uses a serial interface over a wide 
area connection, this sample describes only the options involved with a serial 
configuration.

Nortel Networks recommends that you follow this procedure when you fill out the 
worksheets:

1.

Fill out the Global Information worksheet completely.

The sample worksheet lists options common to all serial interface 
configurations.

2.

After you record your protocol selections on the Global Information 
worksheet, fill out one Router Protocol worksheet. 

Table B-1.

Quick-Start Connector Names and Numbers

Module

Interface*

* The Quick-Start script does not support initial ISDN or V.34 interface configuration. 

System 
Processor Expansion

WAN 
Adapter 3

WAN 
Adapter 4

WAN 
Adapter 5

Dual 
Ethernet

XCVR1
XCVR2

N/A

N/A

N/A

N/A

ATM T1/E1

ATM1

N/A

N/A

N/A

N/A

Dual 
synchronous

N/A

PORT1,
PORT2

N/A

N/A

N/A

FT1/T1, or 
FE1/E1 
DSU/CSU

N/A

N/A

COM1

COM1

COM1

Note: 

This section provides worksheets only for a serial interface 

configuration over a wide area connection. It does not contain worksheets for 
LAN configuration options. If you are configuring a LAN interface, read the 
Quick-Start text and prompts carefully before responding. 

Summary of Contents for Passport 5430





























































































































































































































Reviews:

No comments