Nortel Passport 5430 Installing And Operating Instructions Download Page 84

Page: 84 / 220

Installing and Operating the Passport 5430 Multiservice Access Switch

4-6

306308-A Rev 00

Route the cable through the cable loom slot corresponding to the
expansion card to which you are attaching the cable.

For instructions, see

“Using the Cable Looms to Manage Cables

” on

page 4-17

Connect the cable to a dual synchronous (Dsync) module interface

(Figure 4-5)

Figure 4-5.

Connecting a Serial Cable to the Dual Synchronous Module Interface

Secure the cable to the interface using the captive screws on the cable.

Arrange the cable in the cable loom.

For instructions, see

“Using the Cable Looms to Manage Cables

” on

page 4-17

Connect the remote end of each cable to the appropriate communications
equipment.

Module 3

Module 4

Module 5

Remote
Console

System

Processor

Expansion Card

Voice Processor

COM

ISDN BRI

withNT1

Telco

V.34 Modem

COM

FBR0077A

PCI Slot 1

PCI Slot 2

PCI Slot 3

PCI Slot 4

Summary of Contents for Passport 5430





























































































































































































































Search results

Summary of Contents for Passport 5430

Reviews:

Nortel Passport 5430, Installing And Operating Instructions, Page: 84 / 220

Search results

Summary of Contents for Passport 5430

Reviews: