Nortel Passport 5430 Installing And Operating Instructions Download Page 72

Page: 72 / 220

Installing and Operating the Passport 5430 Multiservice Access Switch

3-6

306308-A Rev 00

Removing a PMC Module Filler Panel

To remove a PMC module filler panel:

If necessary, remove the card on which the PMC module filler panel is
installed.

For instructions, see Chapter 7, “Replacing the System Processor Card” or
Chapter 9, “Adding or Replacing an Expansion Card.”

Push the PMC module filler panel out from behind the card bezel.

(Figure 3-4)

Figure 3-4.

Removing or Installing a PMC Module Filler Panel

For instructions on installing a PMC module for the first time, see “Installing
a PMC Module on the System Processor Card” on page 2-9 or “Installing a
PMC Module on the Expansion Card” on page 2-12.

For instructions on adding a PMC module on an installed Passport 5430, see
“Adding or Replacing a PMC Module on the System Processor Card” on
page 8-2 or “Adding or Replacing a PMC Module on the Expansion Card” on
page 8-10.

FBR0058A

Expansion Card

Summary of Contents for Passport 5430





























































































































































































































Search results

Summary of Contents for Passport 5430

Reviews:

Nortel Passport 5430, Installing And Operating Instructions, Page: 72 / 220

Search results

Summary of Contents for Passport 5430

Reviews: