Nortel Passport 5430 Installing And Operating Instructions Download Page 182

Page: 182 / 220

Installing and Operating the Passport 5430 Multiservice Access Switch

A-2

306308-A Rev 00

If you are installing your Passport 5430 in an equipment rack, make sure that the
rack meets the following specifications:

•

Heavy-duty steel construction

•

Electronic Industries Association (EIA) standard hole-spacing

•

Width of 19 in. (48.26 cm)

•

Depth of 24 in. (60.96 cm)

Electrical Specifications

Your installation site must meet the following power requirements:

•

Proximity to wall receptacle: within 6 ft (1.8 m) of the Passport 5430

•

Voltage: 90 to 240 VAC

•

Amperage: 1.0 A

Table A-1

lists the wall outlet requirements.

Environmental Specifications

The environmental requirements for the Passport 5430 are as follows:

•

Altitude: 0 to 8000 ft (0 to 2438.4 m)

•

Humidity: 10% to 90%, noncondensing

•

Temperature: 50

to 95

F (10

to 35

C) stable

Table A-1.

Passport 5430 Wall Outlet Requirements

Country

Outlet

Voltage

United States/
Canada

National Electrical Manufacturers
Association (NEMA) 5-15P standard outlet

100 to 120 V

Any other country Your Passport 5430 distributor informs you

of the outlet that you need.

100 to 240 V

Summary of Contents for Passport 5430





























































































































































































































Search results

Summary of Contents for Passport 5430

Reviews:

Nortel Passport 5430, Installing And Operating Instructions, Page: 182 / 220

Search results

Summary of Contents for Passport 5430

Reviews: