manualshive.com logo in svg

Nortel Passport 5430, Installing And Operating Instructions, Page: 119 / 220

Share
Download
Nortel Passport 5430 Installing And Operating Instructions Download Page 119

Operating the Passport 5430

306308-A Rev 00

6-9

Turning the Passport 5430 On and Off

To turn on the Passport 5430:

1.

Press the power switch on the power supply to the on (1) position 

(Figure 6-5)

.

2.

If a redundant power supply is installed, turn it on. 

Figure 6-5.

Passport 5430 Power Switch

3.

Verify that the power output LED for each power supply lights green.

The LED on the power supply is labeled DC OK. If the LED is not on, replace 
the power supply (see “Replacing a Power Supply” on page 11-3).

4.

Verify that air is flowing from the cooling fans out through the side and 
rear of the Passport 5430.

If you cannot feel air flow from the Passport 5430 vents, or if the power output 
LED remains off, do the following:

1.

Turn the power switch on each of the power supplies to the off (0) 
position. 

2.

Verify that the power cable is inserted correctly into the power outlet.

See “Connecting to the AC Power Source” on page 4-16 for information.

FBR0031A

DC OK

PS1

PS2

Power supplies

DC OK

Power switch

Summary of Contents for Passport 5430





























































































































































































































Reviews:

No comments