manualshive.com logo in svg

Nortel Passport 5430, Installing And Operating Instructions, Page: 116 / 220

Share
Download
Nortel Passport 5430 Installing And Operating Instructions Download Page 116

Installing and Operating the Passport 5430 Multiservice Access Switch

6-6

306308-A Rev 00

Table 6-3

 describes the expansion card LED.

PMC Module LEDs

When the Passport 5430 has an optional PMC module installed, its interface LEDs 
are visible on the front panel. For the location of the Passport 5430 PMC module 
bezel openings on the Passport 5430, see Figure 2-2 on page 2-4.

Dual Synchronous PMC Module LEDs

Figure 6-3

 shows the location of the LEDs on the dual synchronous PMC module.

Figure 6-3.

Passport 5430 Dual Synchronous PMC Module LEDs

Table 6-3.

Expansion Card LED

LED

State

Meaning

Insert/Extract

Off

Card extraction is not allowed. Note: This LED is 
reserved for future use.

On (green)

Card extraction is allowed. When you insert the 
card, the LED lights until the card insertion is 
complete. Note: This LED is reserved for future 
use. 

FBR0086A

Module 3

Module 4

Module 5

Remote
Console

5V FLASH ONLY

PCMCIA 2

Module 2

Module 1

Port 1

Port 1

Port 2

Insert

Extract

PCMCIA 1

SYNC

LOOP

RED
ALM

TX/RX

SPD

Link

PS1

PS2

Fan

WAN

Mod2

cPCI

Run

Boot

Sys

YEL
ALM

Console

System

Processor

Expansion Card

AT

M

T1/E1

Dsync

Dsync

Port 1

Port 2

Port 1

Port 2

Port 1

Port 2

Insert

Extract

Expansion Card

Insert

Extract

Module 2

Module 1

Module 2

Module 1

Module 2

Module 1

Voice Processor

Dsync

Dsync

COM

U

D 

DD 

B1

B2

RLSD

Serial

ISDN BRI

withNT1

Telco

Tx 

Rx 

RLSD

DTR

V.34 Modem

COM

RLSD

Serial

Port 2

Daul

T1/E1

SYNC

LOOP

RED
ALM

YEL
ALM

SYNC

LOOP

RED
ALM

YEL
ALM

PCI Slot 1

PCI Slot 2

PCI Slot 3

PCI Slot 4

Port 1

Port 2

Summary of Contents for Passport 5430





























































































































































































































Reviews:

No comments