manualshive.com logo in svg

Nortel Passport 5430, Installing And Operating Instructions, Page: 90 / 220

Share
Download
Nortel Passport 5430 Installing And Operating Instructions Download Page 90

Installing and Operating the Passport 5430 Multiservice Access Switch

4-12

306308-A Rev 00

Connecting an External Console Modem

To connect an external modem to the Passport 5430, you need an AT- or
Hayes-compatible modem and the RJ-45 to DB-9 cable and cable adapter kit 
(Order No. AA0011026) that Nortel Networks provided with the Passport 5430.

To connect an external console modem:

1.

Configure the modem, using the parameters in 

Table 4-3

. 

See the modem user guide for instructions.

2.

Turn off the modem.

3.

Route the cable through the cable loom slot corresponding to PCI slot 1. 

For instructions, see 

“Using the Cable Looms to Manage Cables

” on 

page 4-17

.

4.

Insert the 8-pin receptacle end of the modem cable into the Passport 5430 
Console interface 

(Figure 4-8)

.

For pin assignments, see “Local Console Connections” on page A-17.

Summary of Contents for Passport 5430





























































































































































































































Reviews:

No comments