manualshive.com logo in svg

Nortel Passport 5430, Installing And Operating Instructions, Page: 197 / 220

Share
Download
Nortel Passport 5430 Installing And Operating Instructions Download Page 197

Passport 5430 Technical Specifications

306308-A Rev 00

A-17

Local Console Connections

The Passport 5430 front panel contains one console service interface, labeled 
Console; its 8-pin RJ-45 connector provides an RS-232-D serial connection. You 
can use this local console port to connect the Passport 5430 to a laptop PC for 
direct console access.

The Passport 5430 shipping package includes the console cable
(Order No. 307958-A) for connecting devices to the Console port.

Table A-13

 lists console port pin assignments. 

Table A-13.

Local Console Port RJ-45 Pin Assignments

Pin Assignment

Pin No.

Signal Name

Direction

1

CTS Input

2

DSR

Input

3

RXD

Input

4

DCD

Input

5

TXD

Output

6

Ground

7

DTR

Output

8

RTS

Output

1 2 3 4 5 6 7 8

Summary of Contents for Passport 5430





























































































































































































































Reviews:

No comments