manualshive.com logo in svg

Nortel Passport 5430, Installing And Operating Instructions, Page: 117 / 220

Share
Download
Nortel Passport 5430 Installing And Operating Instructions Download Page 117

Operating the Passport 5430

306308-A Rev 00

6-7

Table 6-4

 describes the dual synchronous PMC module LEDs.

ATM T1/E1 PMC Module LEDs

Figure 6-4

 shows the location of the LEDs on the ATM T1/E1 PMC module.

Figure 6-4.

Passport 5430 ATM T1/E1 PMC Module LEDs

Table 6-4.

Dual Synchronous Module LEDs

LED

State

Meaning

Port 1

Off

No data carrier is detected.

On (green)

Data carrier is detected.

Port 2

Off

No data carrier is detected.

On (green)

Data carrier is detected.

FBR0087A

Module 3

Module 4

Module 5

PCI Slot 1

PCI Slot 2

PCI Slot 3

PCI Slot 4

Remote
Console

5V FLASH ONLY

PCMCIA 2

Module 2

Module 1

Port 1

Port 1

Port 2

Insert

Extract

PCMCIA 1

SYNC

LOOP

RED
ALM

TX/RX

SPD

Link

PS1

PS2

Fan

WAN

Mod2

cPCI

Run

Boot

Sys

YEL
ALM

Console

System

Processor

Expansion Card

AT

M

T1/E1

Dsync

Dsync

Port 1

Port 2

Port 1

Port 2

Port 1

Port 2

Insert

Extract

Expansion Card

Insert

Extract

Module 2

Module 1

Module 2

Module 1

Module 2

Module 1

Voice Processor

Dsync

Dsync

COM

U

D 

DD 

B1

B2

RLSD

Serial

ISDN BRI

withNT1

Daul

T1/E1

SYNC

LOOP

RED
ALM

YEL
ALM

SYNC

LOOP

RED
ALM

YEL
ALM

Telco

Tx 

Rx 

RLSD

DTR

V.34 Modem

COM

RLSD

Serial

Port 2

SYNC

LOOP

RED
ALM

YEL
ALM

Summary of Contents for Passport 5430





























































































































































































































Reviews:

No comments