Nortel Passport 5430 Installing And Operating Instructions Download Page 109

Page: 109 / 220

Starting the Passport 5430

306308-A Rev 00

5-11

•

After completing the diagnostic test procedure, the boot process begins. The
Run and Boot LEDs indicate the boot status

(Table 5-3)

•

After the boot process completes, the Boot LED turns off, and the Run LED
lights green, indicating that the Passport 5430 is operational.

If the LEDs on the Passport 5430 light in this sequence, your installation is
successful.

If the LEDs do not light in this sequence, contact your local Nortel Networks
Technical Solutions Center.

Where to Go Next

Use the following table to determine where you want to go next.

Table 5-3.

Boot Status LEDs

Boot Status

Run LED

Boot LED

Boot

Off

Note:

If the Passport 5430 does not contain a WAN adapter module (WAN),

an ATM T1/E1 module (Mod 2), an expansion card (cPCI), or a redundant
power supply (PS2), the LEDs associated with these components remain off.

For information about

Go to

Operating the Passport 5430

Chapter 6

Passport 5430 Technical Specifications

Appendix A

Worksheets for the Quick-Start Procedure

Appendix B

Summary of Contents for Passport 5430





























































































































































































































Search results

Summary of Contents for Passport 5430

Reviews:

Nortel Passport 5430, Installing And Operating Instructions, Page: 109 / 220

Search results

Summary of Contents for Passport 5430

Reviews: