manualshive.com logo in svg

NetApp NearStore R100, Hardware And Service Manual

Share
Download
NetApp NearStore R100 Hardware And Service Manual Download Page 67

Chapter 5: Startup Responses on an R100 System

57

 

Chassis LED responses at startup

Power supply LEDs 

About this section

This section describes the LED responses for the AC power supply in your R100 
chassis. The location of the LEDs is identified and the LED functionality is 
described:

AC power supply 
LEDs

Location of LEDs: 

The following illustration shows the AC power supply 

LEDs on the back panel.

Description of LEDs: 

The following table describes the AC power supply 

LEDs.

LED

State of 
illumination

Explanation

Amber

On

Power supply is receiving AC power.

Off

AC power is not present. 

Green

On

Power supply output is good.

Off

Power supply output is bad.

SWITCH P/S OFF PRIOR

TO REMOVAL/INSERTION

SWITCH P/S OFF PRIOR

TO REMOVAL/INSERTION

Green LED

Amber LED

AC power plug

AC power cord retaining clips

AC power switch

PS1

PS2

Summary of Contents for NearStore R100





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands