manualshive.com logo in svg

NetApp NearStore R100, Hardware And Service Manual

Share
Download
NetApp NearStore R100 Hardware And Service Manual Download Page 114

104

Replacing the NVRAM III battery

 

Replacing the NVRAM III battery

About replacing the 
NVRAM III battery

The NVRAM adapter has one detached, sealed, lead-acid battery that is 
recharged whenever the system is turned on and operating normally. If the battery 
continues to read low after 24 hours of normal system operation, you must 
replace the battery or the NVRAM III adapter.

Note

The NVRAM III adapter in the R100 is different from the NVRAM adapter in 
other models of NetApp chassis and, therefore, is not interchangeable with 
NVRAM adapters from other models of NetApp chassis.

Replacing the NVRAM battery consists of the following two procedures:

◆

“

Removing the NVRAM III battery

” on page 105

◆

“

Installing the NVRAM III battery

” on page 107

Location of the 
NVRAM III battery

The following figure shows the battery location.

Thumbscrews

Connects to 
NVRAM adapter  

Summary of Contents for NearStore R100





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands