manualshive.com logo in svg

NetApp NearStore R100, Hardware And Service Manual

Share
Download
NetApp NearStore R100 Hardware And Service Manual Download Page 127

Chapter 8: Replacing External Chassis Components

117

 

Installing a power 
supply

To install a power supply, complete the following steps.

Step

Action

1

From the console or LCD screen, identify the failed power supply.

Note

The power supply identifiers, PS1 and PS2, are silk-screened onto 
the chassis frame.

2

Turn off the power switch and disconnect the power to the failed 
power supply on the chassis.

Note

The chassis reports a failure for the removed power supply.

3

Lift up the clip lock and unplug the power cord from the chassis 
power supply.

4

Loosen the power supply thumbscrews by turning each thumbscrew 
counterclockwise.

5

Pull the power supply out of the power supply bay in the chassis.

WARNING

WARNING

The power supply is heavy. Support the bottom of the unit while 
removing the unit from its bay.

6

Set the power supply aside.

Step

Action

1

Verify that the switch on the power supply is turned off.

2

Push the power supply, slowly and firmly, into the bay until the power 
supply is firmly seated in the bay.

3

Secure the power supply by turning the thumbscrew clockwise until it 
stops.

Summary of Contents for NearStore R100





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands