manualshive.com logo in svg

NetApp NearStore R100, Hardware And Service Manual

Share
Download
NetApp NearStore R100 Hardware And Service Manual Download Page 136

126

Replacing the CompactFlash unit subassembly

 

5

Remove chassis fans 5-6 to access the CompactFlash card reader 
subassembly cables by following these steps:

1. Loosen the thumbscrews on the chassis fan 5-6 subassembly.

Note

The thumbscrews are torqued at the factory. Use a #2 Phillips 
screwdriver to loosen the thumbscrews.

2. Pull the fan subassembly straight out of the chassis frame.

3. Set the fan subassembly aside.

6

Loosen the two thumbscrews on the CompactFlash card reader 
subassembly.

7

Press on the latches on either side of the connector on the backplane 
to release the connector, then pull out the cable. Reach into the space 
previously occupied by chassis fans 5-6 and unplug the 
CompactFlash card reader data cable from the chassis backplane.

Note

It might be necessary to partially pull the CompactFlash card reader 
subassembly out of the chassis to access the cables.

8

Unplug the CompactFlash card reader power cable from the chassis 
backplane.

9

Pull the CompactFlash card reader subassembly out of the drive bay.

10

Disconnect the data cable and power cable from the back of the 
CompactFlash card reader subassembly and set them aside.

Step

Action

Summary of Contents for NearStore R100





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands