NetApp NearStore R100 Hardware And Service Manual Download Page 132

Page: 132 / 164

122

Replacing the CompactFlash unit subassembly

Replacing the CompactFlash unit subassembly

About this section

This section describes the procedures for replacing the CompactFlash™ unit
subassembly in the R100 chassis. It also includes information about the LEDs on
the front of the CompactFlash unit card reader.

About the
CompactFlash card

The R100 chassis uses a CompactFlash card that plugs into the CompactFlash
card reader.

The CompactFlash card in the reader is the primary boot device.

Topics in this
section

This section provides information about the following topics:

◆

“

Replacing the CompactFlash card

” on page 123

◆

“

Replacing the CompactFlash card reader subassembly

” on page 125

Summary of Contents for NearStore R100





































































































































































Search results

Summary of Contents for NearStore R100

Reviews:

Brands by name

Popular brands

NetApp NearStore R100, Hardware And Service Manual

Search results

Summary of Contents for NearStore R100

Reviews:

Brands by name

Popular brands