manualshive.com logo in svg

NetApp NearStore R100, Hardware And Service Manual

Share
Download
NetApp NearStore R100 Hardware And Service Manual Download Page 126

116

Replacing the power supply in the chassis

 

Replacing the power supply in the chassis

About replacing the 
power supply

This chapter describes the procedures for replacing the hot swappable power 
supplies in your R100 chassis. Replacing a power supply consists of the 
following procedures:

◆

“

Removing a power supply

” on page 116

◆

“

Installing a power supply

” on page 117

Note

To maintain UL, CSA, and TUV safety certifications, you must obtain 
replacement power supplies from Network Appliance.

Power supply 
compatibility

Be aware of the following caution regarding the compatibility between the two 
power supplies in the chassis.

Caution

When replacing a power supply, be sure not to mix two different power supplies. 
The two power supplies in your R100 chassis must have the same part number.

Removing a power 
supply

To remove a power supply, complete the following steps.

WARNING

WARNING

To avoid an electric shock hazard, you must disconnect the power supply 
before removing it from the chassis.

Note

Because you have two power supplies that are hot swappable, you do not have to 
shut down the chassis.

Summary of Contents for NearStore R100





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands