National Instruments VME-MXI-2 User Manual Download Page 27 | Manualshive

Page: 27 / 262

background image

Chapter 2

Functional Overview

© National Instruments Corporation

2-7

VME-MXI-2 User Manual

• VME-MXI-2

Registers

This logic block represents all registers on the VME-MXI-2. The
registers are accessible from either the VMEbus or MXIbus. All
registers are available in the first 4 KB of the VME-MXI-2 A24/A32
memory space, while a subset is accessible in the VME-MXI-2
VXIbus A16 configuration area.

• Onboard DRAM

SIMMs

This logic block represents the two DRAM SIMM sockets on the
VME-MXI-2. If DRAM is installed, it will be accessible in the
VME-MXI-2 A24/A32 memory space that is not mapped to registers
(above 4 KB).

• VMEbus Data

Transceivers

These transceivers ensure that the VME-MXI-2 meets the loading,
driving, and timing requirements of the VMEbus specification for the
D[31–0] signals.

• VMEbus Interrupt

and Utility Signal
Transceivers

These transceivers ensure that the VME-MXI-2 meets the loading,
driving, and timing requirements of the VMEbus specification for the
IRQ*[7–1], SYSRESET*, SYSFAIL*, and ACFAIL* signals.

• Interrupt and Utility

Signal Circuitry

This circuitry handles mapping of the interrupt and utility signals
between the VMEbus and MXIbus. The utility signals include
SYSRESET*, SYSFAIL*, and ACFAIL*. This circuitry also
generates interrupts from other conditions on the VME-MXI-2 and
allows generation of the utility signals.

• MXI-2 Interrupt and

Utility Signal
Transceivers

These transceivers ensure that the VME-MXI-2 meets the loading,
driving, and timing requirements of the MXI-2 specification for the
IRQ*[7–1], SYSRESET*, SYSFAIL*, and ACFAIL* signals.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
25
26
27
28
29
...
»

Summary of Contents for VME-MXI-2







































































































































































































































































Reviews:

No comments

Related manuals for VME-MXI-2

Suprex SPX-7400 Series

Brand: Cypress Pages: 18

Brand: Directed Pages: 16

Brand: X10 Pages: 7

Smart Screen Blender DUO

Brand: Ninja Pages: 15

Brand: SC&T Pages: 4

Brand: LINK-MI Pages: 4

Brand: Luxtronic Pages: 8

Brand: Black Box Pages: 30

Brand: Teesa Pages: 28

SoloCAT Ultra MAX

Brand: Zektor Pages: 8

Brand: VacuBlend Pages: 12

DevicePort Series

Brand: Sunix Pages: 51

Brand: KitchenAid Pages: 5

Brand: KitchenAid Pages: 28

Brand: KitchenAid Pages: 17

Brand: KitchenAid Pages: 4

Brand: KitchenAid Pages: 40

Brand: KitchenAid Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands