manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

xl

MCF5407 User’s Manual

Organization  

— Section 4.3, “SRAM Overview,” describes the MCF5272 on-chip static RAM 

(SRAM) implementation. It covers general operations, configuration, and 
initialization. It also provides information and examples of how to minimize 
power consumption when using the SRAM. 

— Section 4.4, “ROM Overview,” describes the MCF5272 on-chip static ROM. 

The ROM module contains tabular data that the ColdFire core can access in a 
single cycle.

— Section 4.5, “Instruction Cache Overview,” describes the MCF5272 cache 

implementation, including organization, configuration, and coherency. It 
describes cache operations and how the cache interacts with other memory 
structures. 

•

Chapter 5, “Debug Support,” describes the Revision A hardware debug support in 
the MCF5272. 

•

Chapter 6, “System Integration Module (SIM),” describes the SIM programming 
model, bus arbitration, power management, and system-protection functions for the 
MCF5272.

•

Chapter 7, “Interrupt Controller,” describes operation of the interrupt controller 
portion of the SIM. Includes descriptions of the registers in the interrupt controller 
memory map and the interrupt priority scheme. 

•

Chapter 8, “Chip Select Module,” describes the MCF5272 chip-select 
implementation, including the operation and programming model, which includes 
the chip-select address, mask, and control registers.

•

Chapter 9, “SDRAM Controller,” describes configuration and operation of the 
synchronous DRAM controller component of the SIM, including a general 
description of signals involved in SDRAM operations. It provides interface 
information for memory configurations using most common SDRAM devices for 
both 16- and 32-bit-wide data buses. The chapter concludes with signal timing 
diagrams. 

•

Chapter 10, “DMA Controller,” provides an overview of the MCF5272’s 
one-channel DMA controller intended for memory-to-memory block data transfers. 
This chapter describes in detail its signals, registers, and operating modes.

•

Chapter 11, “Ethernet Module,” describes the MCF5272 fast Ethernet media access 
controller (MAC). This chapter begins with a feature-set overview, a functional 
block diagram, and transceiver connection information for both MII and seven-wire 
serial interfaces. The chapter concludes with detailed descriptions of operation and 
the programming model.

•

Chapter 12, “Universal Serial Bus (USB),” provides an overview of the USB module 
of the MCF5272, including detailed operation information and the USB 
programming model. Connection examples and circuit board layout considerations 
are also provided.

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

Samsung AllShare Cast Dongle Quick Start Manual preview
AllShare Cast Dongle
Brand: Samsung Pages: 2
D-Link DSL-2750U Setup preview
DSL-2750U
Brand: D-Link Pages: 14
Rabbit 2000 Designers Handbook preview
2000
Brand: Rabbit Pages: 45
Rabbit 2000 Instruction & Reference Manual preview
2000
Brand: Rabbit Pages: 174
Rabbit 2000 Getting Started preview
2000
Brand: Rabbit Pages: 43
Jetter JXM-IO-E30 Installation Manual preview
JXM-IO-E30
Brand: Jetter Pages: 35
Yamaha mLAN Driver Manual Book preview
mLAN Driver
Brand: Yamaha Pages: 24
Yamaha DSP1D Supplementary Manual preview
DSP1D
Brand: Yamaha Pages: 5
Zhone 6211 Quick Installation Instructions preview
6211
Brand: Zhone Pages: 1
National Instruments NI-9252 Calibration Procedure preview
NI-9252
Brand: National Instruments Pages: 9
Analog Devices Linear SCP-LT8362-S-EVALZ Demo Manual preview
Linear SCP-LT8362-S-EVALZ
Brand: Analog Devices Pages: 8
Telex Communications 2472AA Instruction Manual preview
2472AA
Brand: Telex Communications Pages: 28
IFM Electronic OVP800 Operating Instructions Manual preview
OVP800
Brand: IFM Electronic Pages: 14
DCB BROADCAST POLLING FRAD BPF-14 BU Manual preview
BROADCAST POLLING FRAD BPF-14 BU
Brand: DCB Pages: 28
Alcatel-Lucent 9364 Installation And Commissioning Manual preview
9364
Brand: Alcatel-Lucent Pages: 60
GSA Bolide BN-NVR/NX User Manual preview
Bolide BN-NVR/NX
Brand: GSA Pages: 101
Cypress Semiconductor CY8CNP102B Specification Sheet preview
CY8CNP102B
Brand: Cypress Semiconductor Pages: 38
S&T Kontron CP3005 Series User Manual preview
Kontron CP3005 Series
Brand: S&T Pages: 115

Brands by name

Popular brands

Load more brands