Motorola DigitalDNA ColdFire MCF5272 User Manual Download Page 320 | Manualshive

Page: 320 / 550

background image

13-26

MCF5272 User’s Manual

PLIC Registers

13.5.12 GCI Monitor Channel Receive Registers

(P3GMR–P0GMR)

All bits in these registers are read only and are initialized to 0x00FF on hardware or
software reset.

PLGMR are 16-bit register containing the received monitor channel bits for each of the four
receive ports on the MCF5272.

A byte of monitor channel data received on a certain port is put into an associated register
using the format shown in Figure 13-24. A maskable interrupt is generated when a byte is
written into any of these four registers.

13, 9, 5, 1

GMRn

GCI monitor received. When set, this bit indicates that data has been written to a
monitor channel receive register. An interrupt is queued when this bit is set if the
GMR interrupt enable bit has been set in the corresponding PLICR register. The
GMR bit and associated interrupt are automatically cleared when the corresponding
PLGMR register has been read by the CPU.

12, 8, 4, 0

GMTn

GCI monitor transmitted. When set, this bit indicates that the monitor channel
transmit register is empty. An interrupt is queued when this bit is set if the GMT
interrupt enable bit has been set in the corresponding PLICR register. The GMT bit
and associated interrupt are automatically cleared when the PGMTS register has
been read by the CPU.

15

11

10

9

8

7

0

Field

—

EOM

AB

MC

M

Reset

0000_0000_1111_1111

R/W

Read Only

Addr

MBAR + 0x360 (P0GMR); 0x362 (P1GMR); 0x364 (P2GMR); 0x366 (P3GMR)

Figure 13-24. GCI Monitor Channel Receive Registers (P0GMR–P3GMR)

Table 13-7. P0GMR–P3GMR Field Descriptions

Bits

Name

Description

15–11

—

Reserved, should be cleared.

10

EOM

End of message.
0 Default at reset.
1 Indicates to the CPU that an end-of-message condition has been recognized on

the E bit. EOM is automatically cleared when the PLGMR register has been read
by the CPU.

9

AB

Abort.
0 Default at reset.
1 Indicates that the GCI controller has recognized an abort condition and is

acknowledging the abort. It is automatically cleared by the CPU when the
PLGMR register has been read.

Table 13-6. PASR Field Descriptions (Continued)

Bits

Name

Description

«
...
318
319
320
321
322
...
»

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

Brand: XMG Pages: 5

Brand: NAD Pages: 2

EXPANSION CARD X-DANTE

Brand: Behringer Pages: 65

Brand: Fostex Pages: 20

Brand: hilscher Pages: 154

Emulator MCU Board for 38D5 Group M38D59T-RLFS

Brand: Renesas Pages: 4

Brand: ACTi Pages: 12

Brand: Aaeon Pages: 57

Brand: Juniper Pages: 196

Brand: Digital Voice Systems Pages: 32

Brand: Digital Equipment Pages: 90

Brand: audemat Pages: 93

Brand: Kontron Pages: 14

SPEEDTOUCH 110G

Brand: THOMSON Pages: 26

Brand: Paradyne Pages: 28

ClareVision CV-M161620-04

Brand: Clare Controls Pages: 32

11th Gen Intel Core U-Series

Brand: IBASE Technology Pages: 70

Brand: netsys Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands