manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

Chapter 13.  Physical Layer Interface Controller (PLIC)  

13-19

PLIC Registers

13.5.5  B2 Data Transmit Registers (P3B2TR–P0B2TR)

All bits in these registers are read/write and are set on hardware or software reset.

The PLTB2 registers contain four frames of transmit data for port n of channel B2.
(P0B2TR is the B2 channel transmit data for port 0, P1B2TR is B2 transmit for port 1, and
so on.) The data are packed from LSB to MSB.

These registers are aligned on long-word boundaries from MBAR + 0x338 for P0B2TR to
MBAR + 0x344 for P3B2TR. Please refer to Section 13.2.3, “GCI/IDL B- and D-Channel
Bit Alignment” for the frame and bit alignment within the 32-bit word.

13.5.6  D Data Transmit Registers (P3DTR–P0DTR)

All bits in these registers are read/write and are set on hardware or software reset.

The PLTD registers contain four frames of D-channel transmit data, packed from lsb to
msb, for each of the four physical ports on the MCF5272. P0DTR is the D-channel byte for
port 0, P1DTR the D channel for port 1, and so on.

The four byte-addressable 8-bit registers, P3DTR–P0DTR, are packed to form one 32-bit
register, PLTD. PLTD is aligned on a long-word boundary at MBAR + 0x348 and can be
read as a single 32-bit register. P0DTR is located in the MSB of the PLTD register, P3DTR
is located in the LSB of the PLTD register.

31

24

23

16

Field

Frame0

Frame1

Reset

1111_1111

1111_1111

R/W

Read/Write

15

8

7

0

Field

Frame2

Frame3

Reset

1111_1111

1111_1111

R/W

Read/Write

Addr

MBAR + 0x338 (P0B2TR); 0x33C (P1B2TR); 0x340 (P2B2TR); 0x344 (P3B2TR)

Figure 13-17. B2 Transmit Data Registers P3B2TR–P0B2TR

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

NEC Univerge SV8100 System Configuration Manual preview
Univerge SV8100
Brand: NEC Pages: 44
Omnia 11 Installation And Operation Manual preview
11
Brand: Omnia Pages: 102
Intel Optane M Series Installation And User Manual preview
Optane M Series
Brand: Intel Pages: 59
DAD DPX2060 User Manual preview
DPX2060
Brand: DAD Pages: 32
Commell CMB-673 Installation Manual preview
CMB-673
Brand: Commell Pages: 9
Eaton APS6-400 Series Installation And Operation Manual preview
APS6-400 Series
Brand: Eaton Pages: 114
Bridgeworks Oresund EFC102200 User Manual preview
Oresund EFC102200
Brand: Bridgeworks Pages: 84
ebm-papst W3G710-NK67-01 Operating Instructions Manual preview
W3G710-NK67-01
Brand: ebm-papst Pages: 13
AMD Geode LE-366 User Manual preview
Geode LE-366
Brand: AMD Pages: 45
Compro Technology RS-2104 Quick Installation Manual preview
RS-2104
Brand: Compro Technology Pages: 2
Boss Vocal Performer VE-20 Owner'S Manual preview
Vocal Performer VE-20
Brand: Boss Pages: 20
ExtraHop EDA 4200 Install preview
EDA 4200
Brand: ExtraHop Pages: 2
Aleratec 260206 Quick Start Manual preview
260206
Brand: Aleratec Pages: 16
PairGain T1L2F10A Manual preview
T1L2F10A
Brand: PairGain Pages: 76
M86 Security Web Filter HL User Manual preview
Web Filter HL
Brand: M86 Security Pages: 512
Intel SL6NQ - Xeon 2.4 GHz/533MHz/512 KB CPU Processor 2.4GHz Specification preview
SL6NQ - Xeon 2.4 GHz/533MHz/512 KB CPU Processor 2.4GHz
Brand: Intel Pages: 56
Curtiss-Wright KAD/UBM/105 Quick Start Manual preview
KAD/UBM/105
Brand: Curtiss-Wright Pages: 12
Curtiss-Wright GT200 VME Hardware Reference Manual preview
GT200 VME
Brand: Curtiss-Wright Pages: 58

Brands by name

Popular brands

Load more brands