manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

Chapter  11.  Ethernet Module  

11-35

Buffer Descriptors

The first word of the RxBD contains control and status bits. Its format is detailed below. 

Table 11-34. RxBD Field Descriptions 

Bits

Name

Description

15

E

Empty. Written by the FEC (= 0) and user (= 1). 
0 The data buffer associated with this BD has been filled with received data, or data 
reception has been aborted due to an error condition. The status and length fields have 
been updated as required.
1 The data buffer associated with this BD is empty, or reception is currently in progress.

14

RO1

Receive software ownership. This field is reserved for use by software. This read/write bit is 
not modified by hardware, nor does its value affect hardware.

13

W

Wrap. Written by the user.
0 =The next buffer descriptor is found in the consecutive location.
1 =The next buffer descriptor is found at the location defined in R_DES_START.

12

RO2

Receive software ownership. Reserved for use by software. This read/write bit is not 
modified by hardware, nor does its value affect hardware.

11

L

Last in frame. Written by the FEC.
0 =The buffer is not the last in a frame.
1 =The buffer is the last in a frame. 

10–9

—

Reserved, should be cleared.

8

M

Miss. Written by the FEC. This bit is set by the FEC for frames that were accepted in 
promiscuous mode, but were flagged as a miss by the internal address recognition. Thus, 
while in promiscuous mode, the user can use the M-bit to quickly determine whether the 
frame was destined to this station. Valid only if the L-bit and the PROM bit are set.
0 The frame was received because of an address recognition hit.
1 The frame was received because of promiscuous mode.

7

BC

Broadcast. Written by the FEC. Will be set if DA is broadcast. (FF-FF-FF-FF-FF-FF)

6

MC

Mulitcast. Written by the FEC. Is set if DA is multicast and not BC.

5

LG

Rx frame length violation. Written by the FEC. A frame length greater than MAX_FL was 
recognized. Frames exceeding 2047 bytes are truncated to prevent wrapping hardware 
length counters. Valid only if the L-bit is set.

4

NO

Rx non-octet-aligned frame. Written by the FEC. A frame that contained a number of bits 
not divisible by 8 was received, and the CRC check that occurred at the preceding byte 
boundary generated an error. Valid only if the L-bit is set. If this bit is set, the CR bit is not 
set.

3

SH

Short frame. Written by the FEC. A frame length that was less than the minimum defined 
for this channel was recognized. The FEC does not support SH and this bit is always 
cleared.

2

CR

Rx CRC error. Written by the FEC. Contains a CRC error and is an integral number of 
octets in length. Valid only if the L-bit is set.

1

OV

Overrun. Written by the FEC. A receive FIFO overrun occurred during frame reception. If 
this bit is set, the other status bits, M, LG, NO, SH, CR, and CL, lose their normal meaning 
and are zero. Valid only if the L-bit is set.

0

TR

Truncated receive frame. Written by the FEC. Set if the receive frame is truncated. Frames 
greater than or equal to 2048 bytes are truncated.

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

D-Link DXS-3610-54S Quick Installation Manual preview
DXS-3610-54S
Brand: D-Link Pages: 38
D-Link Web Smart DES-1210-28P Selection Manual preview
Web Smart DES-1210-28P
Brand: D-Link Pages: 6
D-Link xStack Storage DSN-4000 Series Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 23
D-Link Express EtherNetwork DI-604 Brochure preview
Express EtherNetwork DI-604
Brand: D-Link Pages: 7
D-Link xStack Storage DSN-4000 Series Cli User'S Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 97
NEC Univerge SV9300 Migration Manual preview
Univerge SV9300
Brand: NEC Pages: 26
NEC NEAX 2400 Quick Reference Manual preview
NEAX 2400
Brand: NEC Pages: 20
NEC DS2000 IntraMail Instructions preview
DS2000 IntraMail
Brand: NEC Pages: 2
3Com 3CRWEASY96A Quick Start Manual preview
3CRWEASY96A
Brand: 3Com Pages: 8
Farallon NetLINE USB User Manual preview
NetLINE USB
Brand: Farallon Pages: 26
Observint N16 Quick Setup Manual preview
N16
Brand: Observint Pages: 11
Yaesu FT-817 - Modification Instructions preview
FT-817 -
Brand: Yaesu Pages: 2
BSS Audio EC-4B Installation Manual preview
EC-4B
Brand: BSS Audio Pages: 20
Reeven NAIA Installation Manual preview
NAIA
Brand: Reeven Pages: 2
KEMP Technologies LoadMaster 1500 Installation And Configuration Manual preview
LoadMaster 1500
Brand: KEMP Technologies Pages: 71
Dialogic DM/IP601-CPCI-100BT Quick Install Card preview
DM/IP601-CPCI-100BT
Brand: Dialogic Pages: 2
ETC Power Control Processor Configuration Manual preview
Power Control Processor
Brand: ETC Pages: 64
Intel Core 2 Quad Q9400 Product Brief preview
Core 2 Quad Q9400
Brand: Intel Pages: 2

Brands by name

Popular brands

Load more brands