manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

Chapter 21.  IEEE 1149.1 Test Access Port (JTAG)  

21-1

Chapter 21  
IEEE 1149.1 Test Access Port (JTAG)

This chapter describes the dedicated user-accessible test logic implemented on the
MCF5272. This test logic complies fully with the IEEE 1149.1 Standard Test Access Port
and Boundary Scan Architecture. This chapter describes those items required by the
standard and provides additional information specific to the MCF5272 implementation. For
internal details and sample applications, see the IEEE 1149.1 document.

21.1  Overview 

Problems with testing high-density circuit boards led to development of this standard under
the sponsorship of the Test Technology Committee of IEEE and the Joint Test Action Group
(JTAG). The MCF5272 supports circuit board test strategies based on this standard.

The test logic includes a test access port (TAP) consisting a 16-state controller, an
instruction register, and three test registers (a 1-bit bypass register, a 265-bit boundary-scan
register, and a 32-bit ID register). The boundary scan register links the device’s pins into
one shift register. The contents of this register can be found at the ColdFire website at
http://www.motorola.com/semiconductors. Test logic, implemented using static logic
design, is independent of the device system logic. The TAP includes the following
dedicated signals:

•

TCK—Test clock input to synchronize the test logic.

•

TMS—Test mode select input (with an internal pullup resistor) that is sampled on 
the rising edge of TCK to sequence the TAP controller's state machine.

•

TDI—Test data input (with an internal pull-up resistor) that is sampled on the rising 
edge of TCK.

•

TDO—three-state test data output that is actively driven in the shift-IR and shift-DR 
controller states. TDO changes on the falling edge of TCK.

These signals, described in detail in Table 21-1, are enabled by negating the Motorola test
mode signal (MTMOD). TRST is not provided

 

because TAP pins are reset by an internal

power-on reset circuit.

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

XMOS xCORE-200 Multi-channel Audio board Design Manual preview
xCORE-200 Multi-channel Audio board
Brand: XMOS Pages: 112
3Com 3CRSHPW196 User Manual preview
3CRSHPW196
Brand: 3Com Pages: 16
IDT USB-BRIDGEV2-EVAL Evaluation Board Manual preview
USB-BRIDGEV2-EVAL
Brand: IDT Pages: 11
STMicroelectronics ST62GP-EMU2 HDS2 Series User Manual preview
ST62GP-EMU2 HDS2 Series
Brand: STMicroelectronics Pages: 58
Paradyne 7510 DSU Start-Up Instructions preview
7510 DSU
Brand: Paradyne Pages: 10
ICP DAS USA PDS-734D Quick Start Manual preview
PDS-734D
Brand: ICP DAS USA Pages: 8
ZALMAN ZM-MFC1 Combo User Manual preview
ZM-MFC1 Combo
Brand: ZALMAN Pages: 7
Cameo WLG-1801 User Manual preview
WLG-1801
Brand: Cameo Pages: 23
Hauppauge WinTV-DVB Installation And Reference Manual preview
WinTV-DVB
Brand: Hauppauge Pages: 62
Idis DR-6308P Quick Manual preview
DR-6308P
Brand: Idis Pages: 20
Ubiquiti UniFi LED ULED-AT Quick Start Manual preview
UniFi LED ULED-AT
Brand: Ubiquiti Pages: 16
ivideon Bridge B1610 Quick Start Manual preview
Bridge B1610
Brand: ivideon Pages: 11
ADTRAN EXPRESS 6503 User Manual preview
EXPRESS 6503
Brand: ADTRAN Pages: 20
Rockwell Automation Trusted T8833 Manual preview
Trusted T8833
Brand: Rockwell Automation Pages: 21
AMD Geode LX 800 User Manual preview
Geode LX 800
Brand: AMD Pages: 27
EXAGATE SYSGuard 6001 Quick Installation Manual preview
SYSGuard 6001
Brand: EXAGATE Pages: 7
Comelit IPNVR016A User Manual preview
IPNVR016A
Brand: Comelit Pages: 140
Trend Micro R610 Series Quick Start Manual preview
R610 Series
Brand: Trend Micro Pages: 2

Brands by name

Popular brands

Load more brands